This will take you to the main site where there is history, technical information and other information on these cars.
This takes you back to the main page of the forums.
This is the control panel to change your password, information and preferences on this message board.
Click here if your lost your password or need to register on this message board. You must be a registered user to post. Registration is free.
Search this board for information you need.
Click here to buy cool Squarebirds mechandise.
Click here to support Squarebirds.org. For $20 annually receive 20mBytes webspace, a Squarebirds e-mail address and member's icon on the message board.
  #11  
Old 06-19-2010, 11:28 AM
'59 Jim '59 Jim is offline
Newbie
 
Join Date: Jun 17 2010
Posts: 12
'59 Jim is on a distinguished road
Default Got the shop manual

My repair manual arrived yesterday as a matter of fact. Is there a trick to popping off the door and window handles? I read the directions, and followed them, with no success.
Reply With Quote
  #12  
Old 06-19-2010, 02:16 PM
tbird430's Avatar
tbird430 tbird430 is offline
Super-Experienced
 
Join Date: Jun 18 2007
Posts: 2,616
tbird430 is on a distinguished road
Thumbs up

Jim I'd personally recommend you go back with new Motorcraft Platinum spark plugs and try out the new Petronix Ignition system. It replaces the old points & condensor set-up. Just use the "search" engine on this site or google it on the internet.

-Jon in TX.
__________________

The 1960 Ford Thunderbird. The WORLD'S most wanted car....

VTCI Member#6287.
Reply With Quote
  #13  
Old 06-19-2010, 05:51 PM
simplyconnected's Avatar
simplyconnected simplyconnected is offline
Slow Typist
 
Join Date: May 26 2009
Posts: 7,164
simplyconnected is on a distinguished road
Default

Here's a portion of a picture of your door from the Parts Catalog:


Jim, you need a flat, sheetmetal, tool, designed for Ford door handles. They are available everywhere. Simply line-up the tool with the "C" clip on the inside of the handle, and push the clip out. This takes some practice to get it right. The clip is part number 357550-S.
After the clip is out, the handle will pull straight out, and you should be able to put the clip back inside the handle.
I will leave you a PM (Private Message).

Grant, thanks for the kudos. I've been at 12,000 feet in Colorado mountains, and I truly appreciate the affects of pressure drop and thin oxygen. Even modern cars have a hard time breathing, and lose a lot of HP. If you have wrenched on cars up there, you experienced a lot more than most mechanics down here.

Let's help Jim out... I believe most emissions test machines will tell the air:fuel ratio your car is at. We strive for 14.7:1 for efficiency, but you want to run a little richer than that to prevent pre-ignition and detonation. Left running lean, detonation will burn a hole through your pistons (usually down the side).

Richard Hord, I hate to be the bearer of bad news, but if your engine was manufactured before unleaded gas... you need to pull your heads and have hardened exahust valve seats installed. For most of us, that's a good opportunity to have a valve job done. Don't ever go cheap on your heads. They are a MAJOR engine component. - Dave

EDIT: I looked up the official year we started using unleaded gas. For on-road vehicles, it was 1975 (the same year we started using catalytic converters). I got that wrong because my 1980 Harley FXS did NOT have hardened seats, so I had them installed. Apparently motorcycles were not considered to be on-road vehicles. The Clean Air Act banned the sale of leaded fuel for use in on-road vehicles in 1996.
__________________
My latest project:
CLICK HERE to see my custom hydraulic roller 390 FE build.

"We've got to pause and ask ourselves: How much clean air do we need?"
--Lee Iacocca

Last edited by simplyconnected : 06-19-2010 at 06:14 PM. Reason: I did more homework.
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -4. The time now is 05:03 AM.

Driving, racing or working on cars can be hazardous. The procedures and advice on this website including the message board are opinion only. Squarebirds.org and its webmasters and contributors do not guarantee the correctness of the advice and procedures. The Squarebirds.org and its webmasters assume no liability for any damage, fines, punishment, injury or death resulting from following these procedures or advice. If you do not have the skills or tools to repair your car, please consult a professional. By using this site you agree to hold harmless the Squarebirds.org, its authors and its webmasters from any resulting claim and costs that may occur from using the information found on this site.

Powered by vBulletin® Version 3.6.8
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Any submissions to this site and any post on this site becomes property of Squarebirds.org . The webmasters reserve the right to edit and modify any submissions to this site. All material on this is site is copyrighted by the Squarebirds.org. Reproduction by any means other than for personal use is strictly prohibited. Permission to use material on this site can be obtained by contacting the webmasters. Copyright 2002-2016 by Squarebirds.org.