This will take you to the main site where there is history, technical information and other information on these cars.
This takes you back to the main page of the forums.
This is the control panel to change your password, information and preferences on this message board.
Click here if your lost your password or need to register on this message board. You must be a registered user to post. Registration is free.
Search this board for information you need.
Click here to buy cool Squarebirds mechandise.
Click here to support Squarebirds.org. For $20 annually receive 20mBytes webspace, a Squarebirds e-mail address and member's icon on the message board.
  #1  
Old 03-25-2004, 03:04 PM
1rancher 1rancher is offline
Apprentice
 
Join Date: Sep 10 2003
Posts: 79
1rancher is on a distinguished road
Default CAMSHAFTS

HI
i have been having a hard time finding a cam for the earlier fe motors let alone something with a little bump. I hear that you can drill the old fe motors for the cover to take the 1963 and up cams but has anyone done this? Also how about regrinding a stock one and who might be a good choice for that?
thanks
mark
Reply With Quote
  #2  
Old 03-25-2004, 04:55 PM
Alexander's Avatar
Alexander Alexander is offline
Webmaster
 
Join Date: Oct 30 2002
Posts: 3,338
Alexander is on a distinguished road
Default RE: CAMSHAFTS

It would be difficult to find a performance camshaft for the pre-1963 thrust button camshaft retention system. They are available for about $150 from many Thunderbird part suppliers. I warn you to get the timing gear as a set with the camshaft, since there are apparently two different spacings of the interlock peg. I bought a new camshaft to replace the used one on the rebuilt engine I had, but the camshaft would not fit the new timing gear that was on the engine. Frustration.

The engine can be machined for the post-1963 thrust plate system. This system uses a camshaft with a different face than the thrust button type of camshafts. The timing gears are also different.

If you go for the thrust plate system, a wealth of camshaft options are available to you, including the ones from Carroll Shelby. They also have a large amount of FE parts that fit our engine that are hard to get otherwise. I bought a damper spacer and block to head dowels from them. These are new parts that are next to impossible to get elsewhere. http://www.carrollshelbyent.com/engine_order_form.cfm .

Steve Christ's book on rebuilding FE engines is an excellent reference for doing any work on these engines. http://www.amazon.com/exec/obidos/tg...48742?v=glance

Alexander
1959 Hardtop
1960 Golde Top
__________________
Alexander
1959 Hard Top
1960 Golde Top
Reply With Quote
  #3  
Old 03-30-2004, 10:45 PM
pirate pirate is offline
Newbie
 
Join Date: Mar 28 2004
Posts: 18
pirate
Default RE: CAMSHAFTS

Pre 63 Cams can be reground at Lanatti Cams in Memphis Tenn. I agree with Alexander, I would go with the thrust plate and a whole new world is available, in fact a 427 1968 juice cam will work in a 352. This is the only year they had it. You know early 1958 352 Ford engines had solid lifters that were hollow with long pushrods.They discontinued and then made available in 1960. Had heavy lifters cut in the center with much shorter push rods. Holmam Moody had lifters that looked like drill bits for 427s, I have a set. The 68 juice cam has a oil ring on the 3rd bearing race but it will not bother the 352 because it will just put more oil to that bearing. Side oilers all had that and you cannot run pre 65 cams in the unless you machine the oil groove in them. The rockers will not oil.
Reply With Quote
  #4  
Old 04-08-2004, 12:51 PM
KULTULZ
 
Posts: n/a
Default RE: CAMSHAFTS

Maybe this will help with the production break on the FE camshaft. If the image is not large enough to read...right click on it and go to the address under PROPERTIES and there is a blow-up available there.

http://hotrodders.com/gallery/data/5...t_info-med.jpg

Here is the address of the gallery hosting this photo...you will be able to blow it up there;

http://hotrodders.com/gallery/showga...php?ppuser=422
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -4. The time now is 06:03 PM.

Driving, racing or working on cars can be hazardous. The procedures and advice on this website including the message board are opinion only. Squarebirds.org and its webmasters and contributors do not guarantee the correctness of the advice and procedures. The Squarebirds.org and its webmasters assume no liability for any damage, fines, punishment, injury or death resulting from following these procedures or advice. If you do not have the skills or tools to repair your car, please consult a professional. By using this site you agree to hold harmless the Squarebirds.org, its authors and its webmasters from any resulting claim and costs that may occur from using the information found on this site.

Powered by vBulletin® Version 3.6.8
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Any submissions to this site and any post on this site becomes property of Squarebirds.org . The webmasters reserve the right to edit and modify any submissions to this site. All material on this is site is copyrighted by the Squarebirds.org. Reproduction by any means other than for personal use is strictly prohibited. Permission to use material on this site can be obtained by contacting the webmasters. Copyright 2002-2016 by Squarebirds.org.