This will take you to the main site where there is history, technical information and other information on these cars.
This takes you back to the main page of the forums.
This is the control panel to change your password, information and preferences on this message board.
Click here if your lost your password or need to register on this message board. You must be a registered user to post. Registration is free.
Search this board for information you need.
Click here to buy cool Squarebirds mechandise.
Click here to support Squarebirds.org. For $20 annually receive 20mBytes webspace, a Squarebirds e-mail address and member's icon on the message board.
  #1  
Old 02-24-2017, 11:36 PM
hpozz33 hpozz33 is offline
Newbie
 
Join Date: Feb 17 2017
Posts: 3
hpozz33 is on a distinguished road
Default axle leak

I found that gear oil is leaking from behind my rr wheel. I would think that its the axle seal that said how do I pull the axle and replace the seal. Is there a video that outlines the job or least some pictures that can help me get the job done.
hpozz33
pasta553@comcast.net

please disregard I found how to search and got what I needed

Last edited by hpozz33 : 02-24-2017 at 11:52 PM.
Reply With Quote
  #2  
Old 02-25-2017, 02:28 PM
Yadkin Yadkin is offline
Banned
 
Join Date: Aug 11 2012
Posts: 1,910
Yadkin is on a distinguished road
Default

Sometimes the axle corrodes in the seal area. If so a sleeve repair kit can be done by a professional.
Reply With Quote
  #3  
Old 02-26-2017, 12:58 PM
Deanj Deanj is offline
Experienced
 
Join Date: Nov 26 2015
Posts: 385
Deanj is on a distinguished road
Default

Those are the rear axle seals leaking. There is a 1965 Mustang You Tube video that outlines how to replace. Copy this link: https://www.youtube.com/watch?v=P0N23m0Zr3w Important note that on Squarebirds you'll need a slide hammer to pull the axles, then use the same slide hammer to pull the seals, and you'll need a seal installer to install the new seals to make this project easy.

I went to O'Reilly's and bought 2 seals and 4 axle backing plate gaskets (the manual calls for 1 on each side) . The parts store will "rent" a slide hammer with all the attachments and a seal installer. The rental is free, but you pay for the tools and get a full refund upon return.

Basically, remove the drum to expose the axle end. It will have an access hole to unbolt the 4 bolts holding the axle. Use your lugs to bolt up the slide hammer puller and remove the axle. Use the slide hammer with a seal puller attachment to remove the seal. Clean the axle end and install the new seal with the installer and a hammer. Clean off the old axle backing plate seals and install new ones with Permatex Aviation form a gasket. That's what I like to use. Reinstall the axles and torque to 35 foot-pounds. Don't forget the brake-kleen if you need to tidy up the brakes. Re-install drum and wheel.

Dean
Reply With Quote
  #4  
Old 02-26-2017, 01:36 PM
Yadkin Yadkin is offline
Banned
 
Join Date: Aug 11 2012
Posts: 1,910
Yadkin is on a distinguished road
Default

It's always a good idea to take this opportunity to completely clean out the rear end, old lubricant and sludge. Take the drive shaft out, remove the pinion gear set, drain the fluid, then use a broom handle to push a rag down both shaft sides and move it at the center. Do that several times, get it all nice and clean for it's next 50 years of service.

Order a pinion gasket or used grey RTV. Change out the U-joint at the rear since you'll have it out anyway.
Reply With Quote
  #5  
Old 02-26-2017, 04:19 PM
scumdog's Avatar
scumdog scumdog is offline
Super-Experienced
 
Join Date: May 12 2006
Posts: 1,355
scumdog is on a distinguished road
Default

Instead of a slide hammer you can sometimes get away with putting the brake drum back on inside-out, put on three wheel nuts on about 6 turns each and also tapered end out.
Then use the drum as a poor mans slide hammer - I use old drums for this 'just in case'!

NB: it won't work EVERY time, especially if the axles haven't been out for a long time, you may still have to get hold of an axle puller.

And I use RTV instead of those thin paper gaskets that you are meant to use with the axle retaining plate.
__________________
A Thunderbirder from the Land of the Long White Cloud.
Reply With Quote
  #6  
Old 02-26-2017, 07:03 PM
simplyconnected's Avatar
simplyconnected simplyconnected is offline
Slow Typist
 
Join Date: May 26 2009
Posts: 7,163
simplyconnected is on a distinguished road
Default

These are all good suggestions and you should take this opportunity, spend extra time and do the job right. I like using 'free' tools from the major auto parts stores. As an alternative to the loose brake drum, I have used a loose wheel (yep the whole thing). It has more mass to jerk that axle out.

I particularly like Yadkin's suggestion about washing the axle out. This is important. You may need to buy extra gaskets but fresh, clean gear lube in a clean housing should be done at least once per 60,000 miles. Tiny metal particles lodge in nooks all over the inside of your housing. For solvent, I use diesel fuel or kerosene (not gasoline). It's safe, cheap and it washes oil nicely.

If you have a limited slip diff, don't forget to add friction modifier for the clutch plates.

If you use sealer, make sure it is 'oil compatible' like Permatex Black. Regular silicone will break down in oil and it becomes a gummy mess. - Dave
__________________
My latest project:
CLICK HERE to see my custom hydraulic roller 390 FE build.

"We've got to pause and ask ourselves: How much clean air do we need?"
--Lee Iacocca
Reply With Quote
  #7  
Old 02-26-2017, 09:36 PM
Astrowing Astrowing is offline
Experienced
 
Join Date: Jul 22 2009
Posts: 469
Astrowing is on a distinguished road
Default

I have used a length of chain and a short 2x4 and a sledge hammer to tap the axles out
__________________


CLICK HERE for Jim's web site
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -4. The time now is 02:46 PM.

Driving, racing or working on cars can be hazardous. The procedures and advice on this website including the message board are opinion only. Squarebirds.org and its webmasters and contributors do not guarantee the correctness of the advice and procedures. The Squarebirds.org and its webmasters assume no liability for any damage, fines, punishment, injury or death resulting from following these procedures or advice. If you do not have the skills or tools to repair your car, please consult a professional. By using this site you agree to hold harmless the Squarebirds.org, its authors and its webmasters from any resulting claim and costs that may occur from using the information found on this site.

Powered by vBulletin® Version 3.6.8
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Any submissions to this site and any post on this site becomes property of Squarebirds.org . The webmasters reserve the right to edit and modify any submissions to this site. All material on this is site is copyrighted by the Squarebirds.org. Reproduction by any means other than for personal use is strictly prohibited. Permission to use material on this site can be obtained by contacting the webmasters. Copyright 2002-2016 by Squarebirds.org.