This will take you to the main site where there is history, technical information and other information on these cars.
This takes you back to the main page of the forums.
This is the control panel to change your password, information and preferences on this message board.
Click here if your lost your password or need to register on this message board. You must be a registered user to post. Registration is free.
Search this board for information you need.
Click here to buy cool Squarebirds mechandise.
Click here to support Squarebirds.org. For $20 annually receive 20mBytes webspace, a Squarebirds e-mail address and member's icon on the message board.
  #1  
Old 02-02-2014, 10:23 AM
Fireball's Avatar
Fireball Fireball is offline
Apprentice
 
Join Date: Nov 17 2012
Posts: 56
Fireball is on a distinguished road
Default Valve stem seals

Todays task was to change stem seals, these were my key to success. I made an adapter from old sparkplug to pressurize the cylinder.



Not much left of the old ones


I've used better tools but this one was quite OK too



Less than three hours they were all changed
Reply With Quote
  #2  
Old 02-02-2014, 06:45 PM
simplyconnected's Avatar
simplyconnected simplyconnected is offline
Slow Typist
 
Join Date: May 26 2009
Posts: 7,129
simplyconnected is on a distinguished road
Default

Good job! Next, take your rocker shafts off and clean out all the oil holes, in the rocker arms and shafts. CLICK HERE Back in the day we used non-detergent oil. Sediment filled the rocker arm holes and eventually plugged them. A small drill bit or stiff steel wire will open them again. Old stagnant oil remains in the shafts that turns to light grease. Be careful, it will not come out of your clothes. This cleaning costs nothing to do. If you find your shafts are worn, they are available at the parts stores.

I never liked the 'umbrella' seals from back in the day. They harden, split, travel with the valve stem and sometimes they break. In any case, they sure don't do a very good job of holding oil back.

Modern heads use Viton seals. They have a circular spring that holds them on the tower and they don't harden. The old stuff was made from straight neoprene.

Keep up the good work. - Dave
__________________
My latest project:
CLICK HERE to see my custom hydraulic roller 390 FE build.

"We've got to pause and ask ourselves: How much clean air do we need?"
--Lee Iacocca
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -4. The time now is 11:46 PM.

Driving, racing or working on cars can be hazardous. The procedures and advice on this website including the message board are opinion only. Squarebirds.org and its webmasters and contributors do not guarantee the correctness of the advice and procedures. The Squarebirds.org and its webmasters assume no liability for any damage, fines, punishment, injury or death resulting from following these procedures or advice. If you do not have the skills or tools to repair your car, please consult a professional. By using this site you agree to hold harmless the Squarebirds.org, its authors and its webmasters from any resulting claim and costs that may occur from using the information found on this site.

Powered by vBulletin® Version 3.6.8
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Any submissions to this site and any post on this site becomes property of Squarebirds.org . The webmasters reserve the right to edit and modify any submissions to this site. All material on this is site is copyrighted by the Squarebirds.org. Reproduction by any means other than for personal use is strictly prohibited. Permission to use material on this site can be obtained by contacting the webmasters. Copyright 2002-2016 by Squarebirds.org.