This will take you to the main site where there is history, technical information and other information on these cars.
This takes you back to the main page of the forums.
This is the control panel to change your password, information and preferences on this message board.
Click here if your lost your password or need to register on this message board. You must be a registered user to post. Registration is free.
Search this board for information you need.
Click here to buy cool Squarebirds mechandise.
Click here to support For $20 annually receive 20mBytes webspace, a Squarebirds e-mail address and member's icon on the message board.
Old 01-05-2014, 06:48 AM
deviot deviot is offline
Join Date: Aug 1 2013
Posts: 55
deviot is on a distinguished road
Default New coil springs

Hi all,
I just purchased a pair of new front coil springs from thunderbirdhq. The old coils had been cut by the previous owner making the car too low and also lop sided.

In reading the manual I should be able to push the lower wishbone with my foot and hook the spring on and then lift it back up the the jack. The spring appears to be far too tall to do this.

I was looking an using the coil spring compressors on the inside of the coil but I don't think I'll be able to undo them to take them out again. If I put them on the outside of the coil I don't think then will fit up in the frame.

I'm wondering if the coils are make to the original specs.

Has anyone had experience with this?


Reply With Quote
Old 01-05-2014, 09:00 AM
Fireball's Avatar
Fireball Fireball is offline
Join Date: Nov 17 2012
Posts: 56
Fireball is on a distinguished road

If my memory serves correctly, some years need a special tool and some can be done with regular compressors. Try searching the forums it must have been discussed here.

Last edited by Fireball : 01-05-2014 at 09:18 AM.
Reply With Quote
Old 01-05-2014, 11:05 AM
Dakota Boy's Avatar
Dakota Boy Dakota Boy is offline
Join Date: Jun 30 2009
Posts: 1,536
Dakota Boy is on a distinguished road

The front of the car has to be jacked up pretty high first; so the lower control arm can be pushed downwards far enough. Also, remove the UPPER control arm bumper (this allows the spindle to drop a few more inches, and makes it a bit easier to get the lower control arm's ball joint into the spindle.

No spring compressors are needed. I did the job myself a few winters ago. It was fairly nerve-wracking, but I followed the Ford manual's instructions, and found good information (as always) right here on this site.

Another member (dgs) here had posted some photos of the job:

Last edited by Dakota Boy : 01-05-2014 at 11:24 AM.
Reply With Quote
Old 01-05-2014, 10:17 PM
simplyconnected's Avatar
simplyconnected simplyconnected is offline
Slow Typist
Join Date: May 26 2009
Posts: 7,628
simplyconnected is on a distinguished road

If you are going in as deep as 'replacing springs', save some money and a lot of labor by doing all your maintenance at once. You will be so glad you did after it's over.

Don't even try spring compressors, they're useless on a Squarebird.

These "A" arms are very long. That makes them good, stable levers. Think of them as such, and think about how much room you will need to let them swing down before the spring drops out. It literally drops out, into your lap.

I put my cars up on solid jack stands, with frame members perched on them spread as far apart as possible to give the most stability.

Before going under your car, give it a good shake. Make sure it is solid.

Remove the shocks and stabilizer hardware. I have a scissors jack that fits nicely under the lower ball joint, but for now, use it as a 'safety' backup with a small gap. I loosen the nut but leave it on about even with the stud. Then, give it a good rap with my small sledge hammer. (There are several ways to separate a ball joint.) The spring will 'help' separate the ball joint and the nut will contain it as the jack underneath is an added safety measure.

Once loose, raise the scissors jack to take pressure off the nut. Unscrew the nut all the way and lower the scissors jack. The 'A' arm will descend, eventually offering the spring under no pressure.

At this point, I sincerely hope you change all your bushings (US$8.00 each) and change your front stabilizer bar to one that is 1-1/8" in diameter.

Take LOTS of pictures as you go. Remember which shims go where. I use a metal stamp to show where, for example, the 'LF' pivot shaft goes. That way I know which side it's from, witch end is up and which end goes forward. On some cars this doesn't matter, but it did on my '55 because one end was slightly longer than the other.

If the ball joints are worn, they are removed and replaced much easier on your bench than on the car. Some of our members stripped and powder coated their "A" arms, making them look brand new.

New spring installation is exactly opposite. Tape the rubber biscuit on top (I use electrical tape). Rotate until the spring's bottom end rests in the pocket, then raise it with a scissors jack until the lower ball joint enters the spindle. If the car raises off your jack stand, put your wife on the fender and it will come back down enough to turn the ball joint nut.

If you're doing the stabilizer (sway)bar, 'fish it in' just before you connect the last ball joint on the last side because it goes through your 'A' arms.

One last important note: Do not tighten your new rubber bushings until the car is 'sitting' level. Tightening in any other position will hyper rotate the urethane and cause it to fail early. You will notice, as you take the old bushings out, the car does not rotate on the shafts, in fact the bushings' center sleeves have teeth to hold them in position. It strictly rotates on urethane. - Dave
My latest project:
CLICK HERE to see my custom hydraulic roller 390 FE build.

"We've got to pause and ask ourselves: How much clean air do we need?"
--Lee Iacocca
Reply With Quote
Old 01-05-2014, 11:11 PM
dgs's Avatar
dgs dgs is offline
Join Date: Feb 13 2003
Posts: 934
dgs is on a distinguished road

If you don't have a factory shop manual, get one. All the parts houses stock reprints. It gives directions on removing the spring with a floor jack. Sounds silly, but works great.

I didn't believe it and tried to use an auto parts store spring compressor and as Simply Connected said, it was useless. No room to get it in the spring.

Check out my gallery lined above for some pics. Unfortunately none of getting the spring out as I was more worried about controlling the spring instead of taking pics.

The manual also tells the dimension of stock springs. I remember there were two lengths, I believe the longer one was for the 430 cars but I'm not sure. Some members have posted that replacement springs made their nose too high. Measure them and compare against the factory specs.

My car had the shorter springs with yellow paint markings that were spec'd to be 15 3/4" long. They measured exactly that when i pulled them out so I put the originals right back in.
DGS (aka salguod)
1960 Convertible - Raven Black, Red leather
Reply With Quote

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

All times are GMT -4. The time now is 11:50 PM.

Driving, racing or working on cars can be hazardous. The procedures and advice on this website including the message board are opinion only. and its webmasters and contributors do not guarantee the correctness of the advice and procedures. The and its webmasters assume no liability for any damage, fines, punishment, injury or death resulting from following these procedures or advice. If you do not have the skills or tools to repair your car, please consult a professional. By using this site you agree to hold harmless the, its authors and its webmasters from any resulting claim and costs that may occur from using the information found on this site.

Powered by vBulletin® Version 3.6.8
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
Any submissions to this site and any post on this site becomes property of . The webmasters reserve the right to edit and modify any submissions to this site. All material on this is site is copyrighted by the Reproduction by any means other than for personal use is strictly prohibited. Permission to use material on this site can be obtained by contacting the webmasters. Copyright 2002-2016 by