This will take you to the main site where there is history, technical information and other information on these cars.
This takes you back to the main page of the forums.
This is the control panel to change your password, information and preferences on this message board.
Click here if your lost your password or need to register on this message board. You must be a registered user to post. Registration is free.
Search this board for information you need.
Click here to buy cool Squarebirds mechandise.
Click here to support Squarebirds.org. For $20 annually receive 20mBytes webspace, a Squarebirds e-mail address and member's icon on the message board.
  #1  
Old 07-11-2012, 07:41 PM
jimchooz jimchooz is offline
Newbie
 
Join Date: Jul 11 2012
Posts: 9
jimchooz is on a distinguished road
Default Idle engine

I just picked up a '67 Bird with a 390 motor. The guy I bought it from said it was running great back in 2002 when it was parked. So my question is on prepping for attempting to start.

I'm thinking, changing all fluids and getting a new battery. A friend rec. pulling distributor and spinning oil pump with a drill to coat the motor.

What else?

Thanks!

Jim
Reply With Quote
  #2  
Old 07-11-2012, 08:47 PM
YellowRose's Avatar
YellowRose YellowRose is offline
Super-Experienced and a HELLOFA nice guy
 
Join Date: Jan 21 2008
Posts: 11,893
YellowRose is on a distinguished road
Default Idle engine

Hi Jim, thanks for saving a Tbird from the crusher! Have you registered it with the Thunderbird Registry? If not, you should check it out to see if it is registered and if not do so. Here is the link to it. www.tbirdregistry.com

You can go to the Search engine there, type in the VIN # and it will give you a Registry number if it is registered, or it will come up blank if it is not. If it is not, then you can go through the registration process.

As to what to do before starting the engine, draining and replacing the oil would be good, and other fluids. Put a battery tester on the battery to see if it is still in good condition to be charged up, or replace it. That part about pulling the distributor and spinning the oil pump, I will let some one else comment on this and whatever else one should do with an engine that has been sitting for awhile before starting it.
__________________

Ray Clark - Squarebirds Administrator
'59 Tbird "The Yellow Rose Of Texas" aka "Tweety Bird"
"It's Hip To Be Square"
Thunderbird Registry #33025 VTCI #11178

rayclark07"at"att.net (Home) 210-674-5781 (Cell) 210-875-1411
http://www.squarebirds.org/picture_gallery/TechnicalResourceLibrary/trl.htm
Reply With Quote
  #3  
Old 07-11-2012, 09:24 PM
jimchooz jimchooz is offline
Newbie
 
Join Date: Jul 11 2012
Posts: 9
jimchooz is on a distinguished road
Default thanks

Thanks for the info! I'm going to to do allot of research before I attempt to turn that 390 over. I went to the Tbird registry and we weren't listed but we are now!

Looking forward to talking and sharing with everyone on here!

Jim
Reply With Quote
  #4  
Old 07-11-2012, 11:16 PM
simplyconnected's Avatar
simplyconnected simplyconnected is offline
Slow Typist
 
Join Date: May 26 2009
Posts: 7,129
simplyconnected is on a distinguished road
Default

I would pull off the distributor cap and rotate the crank until the rotor points toward #1 spark plug tower, then put the timing marks at TDC. This makes it easy to reset the distributor after manually running the oil pump.

Set your drill motor to run in reverse. The hex oil pump shaft is probably 1/4" so use a socket that can't fall off
(or it may end up at the bottom of the engine).

Pull both valve covers off and watch the oil as it bathes the rocker arms. If you have any that are 'dry' work on them later.

At this point, the distributor may be remounted. If the distributor doesn't fall all the way down, it just means the hex isn't aligned with the oil pump shaft. Hand crank in either direction and it should drop within 1/2 crank turn. Return the timing marks to TDC and notice the rotor. If it points before or after #1, do it again.

Now you can start the engine. Pay attention to the 'dry' rocker arms and notice if they ever lube. If not, pull the shaft and open all the oil holes. None of this work requires money, but a good deal of time. Believe me, it will pay for itself.

When the rockers all work well, replace the covers because you're done. After running the engine, determine if it tends to overheat. If so, remove he starter and core plugs, flush with a garden hose (and a coat hanger), and replace with six brass 1-3/4" core plugs.

These old engines are workhorses but many decades of non-use make them somewhat of a challenge to put back in operation. All rubber needs to be replaced throughout the engine, cooling and fuel system. That small fuel hose coming off the frame is notorious for leaking when you least expect (and far from home). I hope this helps. - Dave
__________________
My latest project:
CLICK HERE to see my custom hydraulic roller 390 FE build.

"We've got to pause and ask ourselves: How much clean air do we need?"
--Lee Iacocca
Reply With Quote
  #5  
Old 07-11-2012, 11:58 PM
jimchooz jimchooz is offline
Newbie
 
Join Date: Jul 11 2012
Posts: 9
jimchooz is on a distinguished road
Default Good advice

Thanks for the tips. Much appreciated! I'll keep you posted on progress!

Jim
Reply With Quote
  #6  
Old 07-12-2012, 09:20 PM
jimchooz jimchooz is offline
Newbie
 
Join Date: Jul 11 2012
Posts: 9
jimchooz is on a distinguished road
Default Idle engine

Thanks for all of the advice. I'm contemplating buying a 2nd '67. There's a decent unit for sale that looks in great shape. The guy says he was in the middle of an engine overhaul and never finished. Only asking $1200 and from the pics, not in to bad of shape. Maybe I can part pull one to the other and get the first one road worthy while I track down parts for the second.

I only paid $1200 for the first so for $2400 I'd have a his and hers?
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -4. The time now is 02:37 PM.

Driving, racing or working on cars can be hazardous. The procedures and advice on this website including the message board are opinion only. Squarebirds.org and its webmasters and contributors do not guarantee the correctness of the advice and procedures. The Squarebirds.org and its webmasters assume no liability for any damage, fines, punishment, injury or death resulting from following these procedures or advice. If you do not have the skills or tools to repair your car, please consult a professional. By using this site you agree to hold harmless the Squarebirds.org, its authors and its webmasters from any resulting claim and costs that may occur from using the information found on this site.

Powered by vBulletin® Version 3.6.8
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Any submissions to this site and any post on this site becomes property of Squarebirds.org . The webmasters reserve the right to edit and modify any submissions to this site. All material on this is site is copyrighted by the Squarebirds.org. Reproduction by any means other than for personal use is strictly prohibited. Permission to use material on this site can be obtained by contacting the webmasters. Copyright 2002-2016 by Squarebirds.org.