This will take you to the main site where there is history, technical information and other information on these cars.
This takes you back to the main page of the forums.
This is the control panel to change your password, information and preferences on this message board.
Click here if your lost your password or need to register on this message board. You must be a registered user to post. Registration is free.
Search this board for information you need.
Click here to buy cool Squarebirds mechandise.
Click here to support Squarebirds.org. For $20 annually receive 20mBytes webspace, a Squarebirds e-mail address and member's icon on the message board.
  #1  
Old 06-21-2012, 10:31 AM
jackbird60 jackbird60 is offline
Experienced
 
Join Date: Nov 28 2008
Posts: 124
jackbird60 is on a distinguished road
Cool Lower Control Arms for 60 Tbird

Hi Everyone,

I originally posted about Lower Control Arm Bushings, since I was told that's what I needed. When I brought my car to my the local car place for repair (and I do trust these guys) and gave them the new bushing they told me that the Lower control arm bushing was welded to the Lower control arm on the drivers side. (they told me I probably didn't need the other control arm, but if I could get one, it would be simplier to do)

Anyway, I breifly searched the iternet for Lower Control Arms and found nothing.

Question is, can they fix that arm? Like just by popping out the old welded bushing, and rewelding the new busdhing to the control arm? I really have no idea on how this would work.

This problem started when I would hear a cracking nosie when I turned the wheel. I found out that it was the lower control arm bushing attached to the front of the frame was popping out and that was the source of the noise.

Any help would be appreciated.

Thanks- Jack
Reply With Quote
  #2  
Old 06-21-2012, 10:57 AM
KULTULZ
 
Posts: n/a
Post

Most likely, the bushing was tacked into place as a result of the original bushing failure and resultant hogging out of the arm bushing opening.

They are hesitant (and rightly so) that once the weld is ground and the bushing removed, the arm will be damaged and they will be stuck with the car on their rack.

They are just covering their butt on this one.
Reply With Quote
  #3  
Old 06-21-2012, 01:06 PM
YellowRose's Avatar
YellowRose YellowRose is offline
Super-Experienced and a HELLOFA nice guy
 
Join Date: Jan 21 2008
Posts: 11,818
YellowRose is on a distinguished road
Default Lower Control Arms for 60 Tbird

Have you called Carl Heller - partsetal on here? Or PM'd him? Carl has a lot of parts for Squarebirds. Or Don at the Bird Nest? Or the Bird House in Delaware? or John Draxler of Tbird Ranch? They all have parts. You can find their contact information in the Advertisements Forum....
__________________

Ray Clark - Squarebirds Administrator
'59 Tbird "The Yellow Rose Of Texas" aka "Tweety Bird"
"It's Hip To Be Square"
Thunderbird Registry #33025 VTCI #11178

rayclark07"at"att.net (Home) 210-674-5781 (Cell) 210-875-1411
http://www.squarebirds.org/picture_gallery/TechnicalResourceLibrary/trl.htm
Reply With Quote
  #4  
Old 06-22-2012, 12:50 AM
simplyconnected's Avatar
simplyconnected simplyconnected is offline
Slow Typist
 
Join Date: May 26 2009
Posts: 7,068
simplyconnected is on a distinguished road
Default

Jack, it's always best to use parts that already fit if they are available. After fifty years many parts become scarce. As a result, many control arms have been repaired successfully.

The lower control arm is very mild stamped steel which is easy to work with. The bushing holes are 'flanged' rather than drilled, and made to give. Bushing shells are stamped, too. The result is two stampings pressed together, neither of which are very exact in size.

I have changed many sets of bushings. Some were tight and some were snug. I have carefully tack welded a few snug-fitting bushings (which works very well). A sloppy fit is not acceptable. If the hole is sloppy but not distorted, a bead (buildup) of weld, ground to size will do nicely.

If the hole is distorted, a new sleeve that a new bushing fits into may be in order. Your fab shop can make a good sleeve by splitting tubing and welding it to the correct diameter, then weld it into the original 'A' arm hole. Give the shop a new urethane bushing set for size and alignment.

My lower 'A' arms have welded spindle 'stop' tabs, so apparently Ford had no problem welding on them. Remember, your suspension rotates on urethane, not on the axle bolts or sleeves. - Dave
__________________
My latest project:
CLICK HERE to see my custom hydraulic roller 390 FE build.

"We've got to pause and ask ourselves: How much clean air do we need?"
--Lee Iacocca
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -4. The time now is 11:45 PM.

Driving, racing or working on cars can be hazardous. The procedures and advice on this website including the message board are opinion only. Squarebirds.org and its webmasters and contributors do not guarantee the correctness of the advice and procedures. The Squarebirds.org and its webmasters assume no liability for any damage, fines, punishment, injury or death resulting from following these procedures or advice. If you do not have the skills or tools to repair your car, please consult a professional. By using this site you agree to hold harmless the Squarebirds.org, its authors and its webmasters from any resulting claim and costs that may occur from using the information found on this site.

Powered by vBulletin® Version 3.6.8
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Any submissions to this site and any post on this site becomes property of Squarebirds.org . The webmasters reserve the right to edit and modify any submissions to this site. All material on this is site is copyrighted by the Squarebirds.org. Reproduction by any means other than for personal use is strictly prohibited. Permission to use material on this site can be obtained by contacting the webmasters. Copyright 2002-2016 by Squarebirds.org.