This will take you to the main site where there is history, technical information and other information on these cars.
This takes you back to the main page of the forums.
This is the control panel to change your password, information and preferences on this message board.
Click here if your lost your password or need to register on this message board. You must be a registered user to post. Registration is free.
Search this board for information you need.
Click here to buy cool Squarebirds mechandise.
Click here to support For $20 annually receive 20mBytes webspace, a Squarebirds e-mail address and member's icon on the message board.
Old 01-14-2012, 02:58 PM
cubbear cubbear is offline
Join Date: Nov 29 2008
Posts: 104
cubbear is on a distinguished road
Default installing 2105 edelbrock intake

installing new intake see it has no provisions for oil fill tube what to do? also how are you mounting temp sender heater hose connection vacumn ect thanks again also no breather
Reply With Quote
Old 01-14-2012, 06:40 PM
59thunder 59thunder is offline
Join Date: Jul 14 2006
Posts: 144
59thunder is on a distinguished road

See my attached picture hope that helps,

Oil fill via valve covers (EDL4462 )

Water temp sender via hole in the centre front of manifold you will need an adapter for the temp sender

And straight coolant hose from water pump onto connector at face of the manifold, and 90 degree fitting out of manifold to heater .

ps Make sure you have good sealant on your manifold

Vacuum at rear of manifold on genuine ford tree

My holley carb (80670) 670 avenger also has vaccum pipe ports as well but i have not used these

The other thing you will have to change is your kick down lever length if you change your carb, as the old lever is not long enough, you will also have to bend your throttle linkage rod as well as it hits the new intake manifold

Good luck Tony
Attached Images
File Type: jpg 105_5223 (2).jpg (316.6 KB, 109 views)
File Type: jpg 105_5224 (2).jpg (377.1 KB, 109 views)
File Type: jpg 105_5226 (2).jpg (301.5 KB, 107 views)
File Type: jpg 105_5227 (2).jpg (368.0 KB, 109 views)
File Type: jpg 105_5228 (2).jpg (225.5 KB, 107 views)
File Type: jpg 105_5044 (2).jpg (428.9 KB, 108 views)

Last edited by 59thunder : 01-14-2012 at 06:56 PM.
Reply With Quote
Old 02-07-2012, 05:15 PM
c4clewis's Avatar
c4clewis c4clewis is offline
Join Date: Aug 18 2010
Posts: 110
c4clewis is on a distinguished road

It's been awhile while I've been moving around and getting settled in, but I just put this manifold on as well (well, like 8 months ago).

You can do as mentioned above, and the Edelbrock valve covers look good. Or, you can just get a grommet kit, drill your existing valve covers and keep a more original look.

BTW, I had a rather large gap underneath the installed intake. "The Right Stuff" RTV worked great with a liberal application to fill the void.

Also, it does mention it in the directions, but if you have the alignment pin for your stock intake, make sure you remove it from the block.
Reply With Quote

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

All times are GMT -4. The time now is 04:05 AM.

Driving, racing or working on cars can be hazardous. The procedures and advice on this website including the message board are opinion only. and its webmasters and contributors do not guarantee the correctness of the advice and procedures. The and its webmasters assume no liability for any damage, fines, punishment, injury or death resulting from following these procedures or advice. If you do not have the skills or tools to repair your car, please consult a professional. By using this site you agree to hold harmless the, its authors and its webmasters from any resulting claim and costs that may occur from using the information found on this site.

Powered by vBulletin® Version 3.6.8
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
Any submissions to this site and any post on this site becomes property of . The webmasters reserve the right to edit and modify any submissions to this site. All material on this is site is copyrighted by the Reproduction by any means other than for personal use is strictly prohibited. Permission to use material on this site can be obtained by contacting the webmasters. Copyright 2002-2016 by