This will take you to the main site where there is history, technical information and other information on these cars.
This takes you back to the main page of the forums.
This is the control panel to change your password, information and preferences on this message board.
Click here if your lost your password or need to register on this message board. You must be a registered user to post. Registration is free.
Search this board for information you need.
Click here to buy cool Squarebirds mechandise.
Click here to support Squarebirds.org. For $20 annually receive 20mBytes webspace, a Squarebirds e-mail address and member's icon on the message board.
  #1  
Old 09-24-2011, 05:49 AM
59thunder 59thunder is offline
Experienced
 
Join Date: Jul 14 2006
Posts: 144
59thunder is on a distinguished road
Default 1959 Door seals

hi all on the home run, almost finished the build, can i have some advice and pictures please

Door seal,
I purchased a pair of door seals from tb headquarters they both seem about 4 to 6 inches too long . i have taped them on to the door to prefit before glueing . I would have thought the door seal would have been tight?

Could someone post a clear picture of there door seals?

Next..... Top door seal to a pillar this is the one that you fit under the two tabs on the front of the door...

Could someone post a clear picture of this too please

Thanks Tony
Reply With Quote
  #2  
Old 09-24-2011, 10:44 AM
Dakota Boy's Avatar
Dakota Boy Dakota Boy is offline
Super-Experienced
 
Join Date: Jun 30 2009
Posts: 1,501
Dakota Boy is on a distinguished road
Default

Door seal = Start at the vent window first. When you get about mid-way on the bottom side of the door, cut it into two pieces. Now take the other end that starts above the door latch and work it down underneath the door until the ends meet. You will have a few inches extra to remove at that point.

Be advised: Some people (including myself) have received door gaskets that were too "fat" at the dogleg area...and then the door wouldnt close. I had to trim mine down with a razor blade.

As for the dogleg seal: There are a couple screws by the drain holes. Not sure why theyre needed cuz the gasket is glued there, but whatever. Leave the tail end unglued so you can just tuck it into the stainless steel trim piece. Here is a photo:
Attached Images
File Type: jpg DSC03337.jpg (461.0 KB, 70 views)
Reply With Quote
  #3  
Old 09-24-2011, 06:56 PM
59thunder 59thunder is offline
Experienced
 
Join Date: Jul 14 2006
Posts: 144
59thunder is on a distinguished road
Default

Thks very much for the picture, i will leave mine taped for a week to settle then i will glue them

This is not the best job, has any one tried double sided 3m tape on this seal?
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -4. The time now is 02:43 AM.

Driving, racing or working on cars can be hazardous. The procedures and advice on this website including the message board are opinion only. Squarebirds.org and its webmasters and contributors do not guarantee the correctness of the advice and procedures. The Squarebirds.org and its webmasters assume no liability for any damage, fines, punishment, injury or death resulting from following these procedures or advice. If you do not have the skills or tools to repair your car, please consult a professional. By using this site you agree to hold harmless the Squarebirds.org, its authors and its webmasters from any resulting claim and costs that may occur from using the information found on this site.

Powered by vBulletin® Version 3.6.8
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Any submissions to this site and any post on this site becomes property of Squarebirds.org . The webmasters reserve the right to edit and modify any submissions to this site. All material on this is site is copyrighted by the Squarebirds.org. Reproduction by any means other than for personal use is strictly prohibited. Permission to use material on this site can be obtained by contacting the webmasters. Copyright 2002-2016 by Squarebirds.org.