This will take you to the main site where there is history, technical information and other information on these cars.
This takes you back to the main page of the forums.
This is the control panel to change your password, information and preferences on this message board.
Click here if your lost your password or need to register on this message board. You must be a registered user to post. Registration is free.
Search this board for information you need.
Click here to buy cool Squarebirds mechandise.
Click here to support Squarebirds.org. For $20 annually receive 20mBytes webspace, a Squarebirds e-mail address and member's icon on the message board.
  #1  
Old 08-20-2011, 05:22 PM
kevin_tbird kevin_tbird is offline
Experienced
 
Join Date: Jun 12 2011
Posts: 157
kevin_tbird is on a distinguished road
Default Wheel Bearing Torque

How tight should the bearing nut be on the front wheels? My shop manual just says to adjust the bearings. It does not give a torque setting. Any recommendations?
Reply With Quote
  #2  
Old 08-20-2011, 09:40 PM
Colo66's Avatar
Colo66 Colo66 is offline
Apprentice
 
Join Date: Aug 10 2008
Posts: 58
Colo66 is on a distinguished road
Default

This is how I do it......
First.....make sure the bearings are "packed" with grease. After everything is installed in the hub, tighten the spindle nut slowly while turning the hub. I read somewhere 15-25 ft lbs but you really don't need to torque, just run the nut in snug then with the lock in position on the nut, back off to the first slot that lines up with the kotter pin hole in the spindle. Thats it! The goal is to have the assembly turn easy with no play at the bearings.

OK.....I'm ready for the flamin' arrows!
__________________
Have you driven a Thunderbird lately......
Reply With Quote
  #3  
Old 08-21-2011, 09:34 AM
Dakota Boy's Avatar
Dakota Boy Dakota Boy is offline
Super-Experienced
 
Join Date: Jun 30 2009
Posts: 1,498
Dakota Boy is on a distinguished road
Default

what he said above


like adjusting the cup-and-cone bearings on a bicycle hub...

set it not so tight that the wheel drags when you spin it, but not so loose that there is side-to-side movement.
Reply With Quote
  #4  
Old 08-21-2011, 10:31 AM
redstangbob redstangbob is offline
Experienced
 
Join Date: Feb 18 2011
Posts: 217
redstangbob is on a distinguished road
Default

Sounds about right. Tapered roller bearings are made to run with a pre-load, so after adjustment make sure there is no play in the hub/rotor without a lot of drag and you'll be fine. If you feel a wiggle, it's not snug enough. JMO Bob C
Reply With Quote
  #5  
Old 08-21-2011, 07:23 PM
simplyconnected's Avatar
simplyconnected simplyconnected is offline
Slow Typist
 
Join Date: May 26 2009
Posts: 7,121
simplyconnected is on a distinguished road
Default

Do you have new races??? <--this is important.

I have had wheels torqued in a similar fashion to the other posts, then found they were extremely loose after no time.

Here's how I do it: While spinning the wheel, torque that nut REAL tight. If a bearing race moves, it should be right now. Then back off the nut and re-tighten to 'snug', not tight.

I did this on my cousin's Amphicar, and much to our HORROR, the nut stripped. If the nut strips, there's something seriously wrong. After careful examination, I found, someone used an English nut on a METRIC spindle. We were both real happy to find the problem right then and there. After finding a correct nut, we again tightened it as hard as we could with no problem. Then I backed it off and brought it to 'snug'.

Always, always, use moly-lithium grease. You want the kind that 'strings' when you pull your greasy fingers apart after packing them well. - Dave
__________________
My latest project:
CLICK HERE to see my custom hydraulic roller 390 FE build.

"We've got to pause and ask ourselves: How much clean air do we need?"
--Lee Iacocca
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -4. The time now is 12:31 AM.

Driving, racing or working on cars can be hazardous. The procedures and advice on this website including the message board are opinion only. Squarebirds.org and its webmasters and contributors do not guarantee the correctness of the advice and procedures. The Squarebirds.org and its webmasters assume no liability for any damage, fines, punishment, injury or death resulting from following these procedures or advice. If you do not have the skills or tools to repair your car, please consult a professional. By using this site you agree to hold harmless the Squarebirds.org, its authors and its webmasters from any resulting claim and costs that may occur from using the information found on this site.

Powered by vBulletin® Version 3.6.8
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Any submissions to this site and any post on this site becomes property of Squarebirds.org . The webmasters reserve the right to edit and modify any submissions to this site. All material on this is site is copyrighted by the Squarebirds.org. Reproduction by any means other than for personal use is strictly prohibited. Permission to use material on this site can be obtained by contacting the webmasters. Copyright 2002-2016 by Squarebirds.org.