This will take you to the main site where there is history, technical information and other information on these cars.
This takes you back to the main page of the forums.
This is the control panel to change your password, information and preferences on this message board.
Click here if your lost your password or need to register on this message board. You must be a registered user to post. Registration is free.
Search this board for information you need.
Click here to buy cool Squarebirds mechandise.
Click here to support Squarebirds.org. For $20 annually receive 20mBytes webspace, a Squarebirds e-mail address and member's icon on the message board.
  #1  
Old 03-09-2011, 10:58 PM
TechStuff TechStuff is offline
Newbie
 
Join Date: Nov 23 2008
Posts: 2
TechStuff is on a distinguished road
Default Brake help for my '55

hi!
I have a '55 that was a barn find. I have been working at it for a number of years and have it in running condition with lots of cosmetic work remaining. I am keeping the car original so restoring and refurbishing alot.

As they stand now, the brakes are in correct operating conditions, most components being new. They just aren't all that good, at least by today's standards.

So - - has anyone reading this managed to convert to disk brakes ? If so what are some effective but economical ways to go about this? Can I keep the same tires?

While I want to keep the car original, if safety or reliability are compromised I don't mind upgrading, as in this case.

Any help appreciated!

Fred
Reply With Quote
  #2  
Old 03-10-2011, 02:39 AM
simplyconnected's Avatar
simplyconnected simplyconnected is offline
Slow Typist
 
Join Date: May 26 2009
Posts: 7,157
simplyconnected is on a distinguished road
Default

Fred, two things weigh heavy here. You either have to keep your car stock or not. There is no inbetween.

Having said that, I have converted both of my Ford Classics ('55 Customline & 59 Galaxie) to power disk brakes.

Power disk brakes will put you through the windshield, they don't pull to the side, they dry out fast and they don't fade. If you drive your '55 in today's traffic I highly recommend you install disk brakes.

Here's the deal (you're in for a treat)... The 1955 Thunderbird and the '55 full-size Ford Cars used the exact same spindles. Here are the Ford Parts Catalog part numbers for 1955 spindles. S=Thunderbird and A=all other Ford cars:



You can use a Granada spindle to take the place of your originals. That means you can put your original spindles in storage in case you ever want to revert back (I guarantee you won't ever go back).

The Granada/Lincoln Versailes setup bolts right on to your original ball joints and the set should include the spindles, calipers, rotors, and backplate (wind catcher). If your wheels are 15", you can probably use the originals. If they are 14", you need Granada-type wheels which are designed to give clearance for the calipers. Several steel wheels fit.

If you are serious about this retrofit, let me know and I will go into more detail. - Dave
__________________
My latest project:
CLICK HERE to see my custom hydraulic roller 390 FE build.

"We've got to pause and ask ourselves: How much clean air do we need?"
--Lee Iacocca

Last edited by simplyconnected : 03-11-2011 at 12:49 AM.
Reply With Quote
  #3  
Old 03-10-2011, 03:08 PM
Joe Johnston Joe Johnston is offline
Super-Experienced
 
Join Date: Dec 23 2008
Posts: 670
Joe Johnston is on a distinguished road
Default

We have a couple of club members that used the Granada swap and have never been happier. It works great. I chose a complete kit from a vendor that included rear wheel cylinders. Smooth installation with full instructions and the 14" wire wheels on my 57 fit with no problem. Any way you go, disks are a big improvement.
Reply With Quote
  #4  
Old 03-12-2011, 09:55 AM
TechStuff TechStuff is offline
Newbie
 
Join Date: Nov 23 2008
Posts: 2
TechStuff is on a distinguished road
Default

Thanks for the encouraging replies!!

Now - - has anyone put together a list of specific parts that I would need??

Fred
Reply With Quote
  #5  
Old 03-13-2011, 12:04 AM
paul274854's Avatar
paul274854 paul274854 is offline
Apprentice
 
Join Date: Mar 10 2011
Posts: 47
paul274854 is on a distinguished road
Default

You might consider the kits that the TBird suppliers have for sale. They do not require changing the spindles like the Granada stuff does. All the parts are enginerred for a TBird. They even have larger rear cylinders to equalize the front and rear brakes.
Reply With Quote
  #6  
Old 03-16-2011, 02:24 AM
simplyconnected's Avatar
simplyconnected simplyconnected is offline
Slow Typist
 
Join Date: May 26 2009
Posts: 7,157
simplyconnected is on a distinguished road
Default

Quote:
Originally Posted by paul274854 View Post
...They even have larger rear cylinders to equalize the front and rear brakes.
Paul, thanks for your post, but rear cylinders need to be much smaller, because front calipers require hundreds of psi more than drum brakes.

When that kind of pressure is applied (usually from a power booster), the rear drum brakes lock up before the fronts can do their job.

The solution is a combination proportioning/metering valve which is installed on ALL disk/drum systems regardless of brand.

You have the right idea, but front brakes do about 80% of the braking. Even with drum/drum systems, the rear brake shoe area is always smaller and so are the piston diameters. We don't want the rear-end to lock up and swing around to the front.

Can you cite a company who offers disk brakes for my '55 without changing spindles? You mentioned, 'suppliers'. Who are they? - Dave
__________________
My latest project:
CLICK HERE to see my custom hydraulic roller 390 FE build.

"We've got to pause and ask ourselves: How much clean air do we need?"
--Lee Iacocca
Reply With Quote
  #7  
Old 03-16-2011, 04:59 AM
Jimz Bird Jimz Bird is offline
Experienced
 
Join Date: Feb 3 2011
Posts: 375
Jimz Bird is on a distinguished road
Default

Disc Brake conversion is one of the first things that I am going t do for "Mable" (Girls always like new shoes) when I get back.

First let me recommend that you go to:
http://www.squarebirds.org/picture_g...ibrary/trl.htm

This is the link under Ray's sig and is available elsewhere.

Scroll down to the section on "Disc Brakes Conversions"

Ray has put a ton of stuff there and I have found it quite useful.

Here is a link to a post there with about 28 pages of discussion that has a lot of good points:
http://www.squarebirds.org/vbulletin...t=5023&page=28
(Scroll down to start at Post 1) Good stuff there!

"WARNING WARNING WARNING Will Robinson"
There is so much good stuff in the Tech Section that you may not be seen for days.

There is also a good Post and Links that Ray and Dave have put together on Combination, Proportioning, metering and residual valves.

BTW Ray - I think one of the links on Proportioning valves has changed. Here is the new one:
http://www.mbmbrakeboosters.com/inde...ters&Itemid=10

There are also a couple of good articles in Gil's Garage:
http://www.ctci.org/gilsgarage/DiscBrakes.php
and here:
http://www.ctci.org/gilsgarage/DiscBrakePerf.php

This last article and the info I got from here prompted me to send a question to CASCO yesterday and ask them about installing a "Residual" valve in addition to their "Kit" and "Combination Valve".

Here also are a couple of shots from their catalog. I am not affiliated and don't want to start a "But this vendor and that vendor" argument but only post them because Dave asked about specific vendors.

I have some other thoughts on replacing the spindles vs. buying a kit but will save those and post them when I get an answer back from CASCO ( http://www.classictbird.com/ ) on the residual valve.

I also think it is good to convert the rears to "Self-Adjusting"

Also a couple of considerations with the new Dual Master Cylinder:
1. a new longer heat shield should be used (Sanderson Headers look like they "aim" down away from the MC and reduce the heat - Yea, that's my excuse to put headers on my want list)
2. probably convert to DOT5
3. another reason for the combination valve is to isolate the front and back systems in case one of the systems fails you still have the other.

I added the Prestige Thunderbird page with their kit also. I couldn't find a Combination valve in their catalog but they may have one or recommend one if you talk with them.

HTH
Attached Images
File Type: png Front Brakes Disc Kit.png (164.8 KB, 58 views)
File Type: png Combination Valve.png (145.7 KB, 60 views)
File Type: png Front Brakes Disc 2a Kit.png (200.6 KB, 58 views)
File Type: png Front Brakes Disc 2b Kit.png (119.2 KB, 58 views)
__________________
Jim
Jimz Greenie with a White Hat and Brown Guts (ZE-XG)


CLICK HERE for Jimz web site

Last edited by Jimz Bird : 03-16-2011 at 06:49 AM. Reason: Added another vendor and notes
Reply With Quote
  #8  
Old 03-16-2011, 01:26 PM
simplyconnected's Avatar
simplyconnected simplyconnected is offline
Slow Typist
 
Join Date: May 26 2009
Posts: 7,157
simplyconnected is on a distinguished road
Default

Jim, your info is fabulous! I didn't know these kits were out there for the '55 and I appreciate you sharing your resources.

Edit: I forgot to ask... are you a restorer? Do you perform brake or suspension work?
__________________
My latest project:
CLICK HERE to see my custom hydraulic roller 390 FE build.

"We've got to pause and ask ourselves: How much clean air do we need?"
--Lee Iacocca

Last edited by simplyconnected : 03-16-2011 at 01:29 PM.
Reply With Quote
  #9  
Old 03-16-2011, 04:46 PM
Jimz Bird Jimz Bird is offline
Experienced
 
Join Date: Feb 3 2011
Posts: 375
Jimz Bird is on a distinguished road
Default

More Info Hot Off the Press - err I mean off the Internet

Here is the response I received from CASCO:

"Jim,

Good questions. The residual pressure valve makes a lot of sense in some applications. We pondered adding it when we began offering the combination (distribution and proportioning) valve. We decided not to add it, because most of the birds out there have the rear brakes properly adjusted and so the extra valve would not be much benefit.

Concerning adding self adjusting mechanism, we have not had any call for this. It might be a good add-on if the car is regularly driven. Unfortunately most of the TBirds arenít driven enough to get the benefit from a self adjusting arrangement. If you do decide to add them, and you have the time to take some pictures and provide your comment, I would really be interested in your take on it.

Regards,
Jim Brown
President CASCO
www.classictbird.com "

So looks like for those of who are "drivers" or want to be when they are ready that either or there may a good consideration.

One more link:
http://www.jalopyjournal.com/forum/s...d.php?t=238124

I am not really a brake or suspension guy - although I have found Anders thread on the 58 suspension fascinating. Especially the geometry and the importance of "length"

I just have been researching this for a while and thought some of the stuff I had found would be valuable in this thread. I am mostly just a lurker here and on the Y-Block Forum. (Seen ya there also Dave)

Thanks for the "accusation" of being a restorer. Coming from Dave - I consider that quite a compliment!
__________________
Jim
Jimz Greenie with a White Hat and Brown Guts (ZE-XG)


CLICK HERE for Jimz web site
Reply With Quote
  #10  
Old 03-16-2011, 09:38 PM
simplyconnected's Avatar
simplyconnected simplyconnected is offline
Slow Typist
 
Join Date: May 26 2009
Posts: 7,157
simplyconnected is on a distinguished road
Default

Thanks, Jim... I'm also a member of the H.A.M.B. Alliance. So is Scarebird, who offers 15% discounts to their paid members.

Self adjusters really shine when your brakes are new-ish, and require frequent adjustment. I have tried 10-lb. residual valves in our '50's Ford cars and I find them to be more dangerous than helpful because there is no indication of how far the wheel pistons are extended. (We used to use the pedal height to indicate when an adjustment is needed.)

Self or manual adjusters spread the bottoms of the shoes and allow the pistons to fully retract every time.

On another note, Ray & I spoke this morning when this dawned on me: How come our members who have Y-Block engines (in their Little Birds) have never posted about valve lash adjustment? Certainly, not everyone knows how to tune a solid lifter engine! I understand the first 352 FE's fall in that catagory too.
__________________
My latest project:
CLICK HERE to see my custom hydraulic roller 390 FE build.

"We've got to pause and ask ourselves: How much clean air do we need?"
--Lee Iacocca
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -4. The time now is 08:14 AM.

Driving, racing or working on cars can be hazardous. The procedures and advice on this website including the message board are opinion only. Squarebirds.org and its webmasters and contributors do not guarantee the correctness of the advice and procedures. The Squarebirds.org and its webmasters assume no liability for any damage, fines, punishment, injury or death resulting from following these procedures or advice. If you do not have the skills or tools to repair your car, please consult a professional. By using this site you agree to hold harmless the Squarebirds.org, its authors and its webmasters from any resulting claim and costs that may occur from using the information found on this site.

Powered by vBulletin® Version 3.6.8
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Any submissions to this site and any post on this site becomes property of Squarebirds.org . The webmasters reserve the right to edit and modify any submissions to this site. All material on this is site is copyrighted by the Squarebirds.org. Reproduction by any means other than for personal use is strictly prohibited. Permission to use material on this site can be obtained by contacting the webmasters. Copyright 2002-2016 by Squarebirds.org.