This will take you to the main site where there is history, technical information and other information on these cars.
This takes you back to the main page of the forums.
This is the control panel to change your password, information and preferences on this message board.
Click here if your lost your password or need to register on this message board. You must be a registered user to post. Registration is free.
Search this board for information you need.
Click here to buy cool Squarebirds mechandise.
Click here to support Squarebirds.org. For $20 annually receive 20mBytes webspace, a Squarebirds e-mail address and member's icon on the message board.
  #1  
Old 12-12-2011, 05:03 PM
shortysbreath shortysbreath is offline
Newbie
 
Join Date: Nov 21 2011
Posts: 14
shortysbreath is on a distinguished road
Default Rebuilt '60 carb free to good home

Hey guys,

I just put an Edelbrock 1406 on my "60, replacing the Autolite 4100 (I think) which has less than 100 miles on a professional rebuild at Carbco here in St.Louis. Carb worked fine when it warmed up. Didn't want to start up when cold (Edelbrock doesn't like to wake up in the morning either).

Anyway, you pay shipping, I'll pop it in the mail.

Any thoughts/advice on continuing cold start problems--just bought Auto Analyzer electrical diagnosis meter, start going through system tomorrow--are appreciated. Car is switched over to Petronix ignition, but still has old coil. Hooked up Edlelbrock electric choke to power window relay.

Phil
314-726-5462 if you want more info on Autolite.
Reply With Quote
  #2  
Old 12-13-2011, 04:19 AM
simplyconnected's Avatar
simplyconnected simplyconnected is offline
Slow Typist
 
Join Date: May 26 2009
Posts: 7,130
simplyconnected is on a distinguished road
Default

This is nothing new, but a few things to check for cold starts:
Cars in the mountains can never get enough air. The rest of us get too much air in cold weather because oxygen is packed much tighter. Without choking the air, our cars start hard in Michigan.

Timing plays a big role, and needs to be retarded a lot for cold starting. Correctly gapped, new spark plugs work the best, and so do correctly gapped points. (I know you have a Pertronix with no points.) If you look at your distributor cap and spark plug wires in the dark, and see any 'stray' sparks between the wires or to ground, it's time to replace ignition parts. Make sure your vacuum advance diaphragm is functioning properly, or your timing may be permanently advanced too much.

We went through 'air' and 'heat', now let's cover 'fuel'... The carb needs a good supply of gasoline, and your accelerator pump must aggressively squirt fuel into your carb when you pump the pedal. I mention this because some carbs leak fuel into the intake as soon as the engine stops (characterized by hard starting with a warm engine). No fuel in the bowl means the engine cannot start until the fuel pump starts delivering gas and the bowl fills.

With the air cleaner off and the temperature cold, observe: When you push the accelerator pedal two things should happen. Your choke cam and butterfly should close and gas should squirt. The owner's manual used to suggest three pumps, then turn the key to 'start'. The choke cam holds the pedal open a little for higher rpm's while the butterfly freely operates off the bi-metal heat spring.

Too bad the old systems didn't temperature-compensate spark timing like new systems do. When is the last time you heard someone 'flooded' their engine in a modern car? We use the same gas, spark plugs, air, etc. Now, more control is taken away from the operator, and precision tuned by a computer.

Old engines that refuse to start may have leaky, bent, or burned valves (or broken rings). To check, I use an air hose plugged into a dummy spark plug and set at 60-100-psi. When the valves are closed and the air is on, there should be no noise coming out of the oil filler, carb or muffler. The slightest leak will cause a very loud hiss. Worn rings may have gaps of .100" which may produce a slight noise. New-ish rings have gaps of ~.020" and are quiet.

Bottom line is, keep your engine maintained and be sure your carburetor's functions are all working properly. - Dave
__________________
My latest project:
CLICK HERE to see my custom hydraulic roller 390 FE build.

"We've got to pause and ask ourselves: How much clean air do we need?"
--Lee Iacocca
Reply With Quote
  #3  
Old 12-13-2011, 04:48 AM
Jimz Bird Jimz Bird is offline
Experienced
 
Join Date: Feb 3 2011
Posts: 375
Jimz Bird is on a distinguished road
Default

Hi Phil,

You may want to hang on to that for a while. That is a good design and if you start up another project and need a quad that is a good one. Depending on the venturi size it also could be fairly valuable especially if it is an original. The venturi size should be stamped on it. It could be a 1.12 (Probably) or a 1.19 which is really valuable.

I was considering the 1.08 as an upgrade to the Holley 4000 on my 56.

Here is what Pony says about it:
http://www.ponycarburetors.com/defau...aqdetail&id=22


If the cold start problem is that after a while it runs better it may be the Heat Riser flapper that is stuck and not directing warm air to the intake.

If you are going to do some electrical TS there is a good article in the Dec issue of Mustang Monthly on checking the charging system. It is for an alternator but the tests still apply.

I'll say it before Dave does but be sure to check all the ground connections while it is cold. Temperature can affect the Cold Cranking Amps that you are drawing. The article covers that also.
http://www.mustangmonthly.com/howto/...tem/index.html

HTH

Sheesh while I was typing and drinking coffee Dave showed up.
__________________
Jim
Jimz Greenie with a White Hat and Brown Guts (ZE-XG)


CLICK HERE for Jimz web site

Last edited by Jimz Bird : 12-13-2011 at 04:50 AM. Reason: Dave still came in 1st
Reply With Quote
  #4  
Old 12-13-2011, 10:18 AM
Anders's Avatar
Anders Anders is offline
Moderator
 
Join Date: Jan 19 2008
Posts: 2,160
Anders is on a distinguished road
Default

Quote:
Originally Posted by shortysbreath View Post
Hey guys,

I just put an Edelbrock 1406 on my "60, replacing the Autolite 4100
What size? 500? 600? 750?
__________________
..."Lil darling Ruth"
http://www.tbirdregistry.com/#33158
Reply With Quote
  #5  
Old 12-13-2011, 10:24 AM
Astrowing Astrowing is offline
Experienced
 
Join Date: Jul 22 2009
Posts: 469
Astrowing is on a distinguished road
Default

I thought the Pertronix system required a new higher voltage coil. In any case, coils are hard to diagnose as the resistance values don't really tell you much other than whether it is shorted or not and we can't measure the secondary voltage directly other than watching the gap jump. Since you have an old one, I'd take a look at it also.
__________________


CLICK HERE for Jim's web site
Reply With Quote
  #6  
Old 12-13-2011, 11:20 AM
shortysbreath shortysbreath is offline
Newbie
 
Join Date: Nov 21 2011
Posts: 14
shortysbreath is on a distinguished road
Default petronix coil

I wasn't sure if I should change the coil or not. Can you ditch the resistor wire since the points are history?
Reply With Quote
  #7  
Old 12-13-2011, 11:43 AM
shortysbreath shortysbreath is offline
Newbie
 
Join Date: Nov 21 2011
Posts: 14
shortysbreath is on a distinguished road
Default

Dave/Jim--Thanks for all the tips. Replaced wires and cap last week. Cleaned ground to chassis (definitely dirty), cleaned positive to starter relay (ditto). Seemed to crank better. If it quits raining, I'll check vacuum advance, start testing the electricals with this fancy pants new meter. I think carb is getting gas, but I'll check again as per your advice. The butterfly is definitely closing all the way. I'm going to put off the bad valve/worn ring analysis until last. And Jim, thanks for tips on old Autolite. I just found a member who wants it so I'm sending it off as per the offer. Someone should use it. And I have enough car parts (Desoto as well as T-Bird) to keep an archeologist busy for a month.

Appreciate all the help you guys. I woke up dreaming about this car this morning.
Reply With Quote
  #8  
Old 12-13-2011, 11:53 AM
shortysbreath shortysbreath is offline
Newbie
 
Join Date: Nov 21 2011
Posts: 14
shortysbreath is on a distinguished road
Default

The autolite is a 600 I think. The edlebrock is the 1406--lean mixture--and also a 600. Bolted right on. Linkage needed adjusting. Runs great. Except for the little cold problem.
Reply With Quote
  #9  
Old 12-13-2011, 03:48 PM
Jimz Bird Jimz Bird is offline
Experienced
 
Join Date: Feb 3 2011
Posts: 375
Jimz Bird is on a distinguished road
Default

Quote:
Originally Posted by shortysbreath View Post
I wasn't sure if I should change the coil or not. Can you ditch the resistor wire since the points are history?
Your welcome.

It is not necessarily the presence of points or not that requires the use of the resistance wire or ballast resistor.

There seems to be a lot of confusion about when to use one and what type of coil to use. I have read that it depends on if it is Ignitor I or II but it appears that the deciding factor is the amount of Amps in the system.

This is a long copy and paste from the Pertronix help section but it may help. (Especially if you have a fancy shmancy meter.) I'm not sure of the rational of the 8 Amps (what determins that and if that changes depending on the system) so I will let Dave clear that up for us.

"What type of coil can I use with the Ignitor™? How do I check my coils resistance? (12V negative ground only)

To determine if your systems coil is compatible with the Ignitor, some measurements should be taken prior to installation of the Ignitor. Caution… While performing this test, never leave the ignition switch on for more than 30 seconds at a time.
Set your voltmeter to a 15 or 20-volt scale. Attach an 18 or 20 AWG jumper wire from the negative coil terminal to an engine ground. Attach positive (red) lead of your voltmeter to the positive side of the coil, and the negative (black) lead to an engine ground. Turn the ignition switch to the run position. Now read the voltage at the positive coil terminal. Turn the ignition switch off. If the voltage measured is approximately 12 volts, no resistance wire is present. A typical resistance wire will provide 9 - 6 volts.
The next step is to determine the resistance in the primary ignition. Label the wires attached to the coil terminals and note their appropriate location. Make sure that the ignition switch is off and disconnect all wires from the coil. Adjust your meter to the lowest ohm scale. If you are using an analog style meter make sure to zero the needle.
Measure from the negative terminal to the positive terminal. Write your measurement down.
Now the maximum system amperage can be determined, divide your voltage measurement by your coil resistance measurement. This will give you the system current or amperage.
Four and six cylinder engines should not exceed 4 amps. Eight cylinder engines should not exceed 8 amps. If the total amperage in your system is higher than the amount recommended for your application, you should install a ballast resistor.
Example

Voltage 12
Resistance 1.5
12 / 1.5 = 8
Total amperage 8 "
__________________
Jim
Jimz Greenie with a White Hat and Brown Guts (ZE-XG)


CLICK HERE for Jimz web site

Last edited by Jimz Bird : 12-13-2011 at 03:50 PM.
Reply With Quote
  #10  
Old 12-13-2011, 06:43 PM
shortysbreath shortysbreath is offline
Newbie
 
Join Date: Nov 21 2011
Posts: 14
shortysbreath is on a distinguished road
Default coil testing

My dad was an electrician. I wish he was around still.

Thanks for the info. You guys are a font.
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -4. The time now is 06:19 PM.

Driving, racing or working on cars can be hazardous. The procedures and advice on this website including the message board are opinion only. Squarebirds.org and its webmasters and contributors do not guarantee the correctness of the advice and procedures. The Squarebirds.org and its webmasters assume no liability for any damage, fines, punishment, injury or death resulting from following these procedures or advice. If you do not have the skills or tools to repair your car, please consult a professional. By using this site you agree to hold harmless the Squarebirds.org, its authors and its webmasters from any resulting claim and costs that may occur from using the information found on this site.

Powered by vBulletin® Version 3.6.8
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Any submissions to this site and any post on this site becomes property of Squarebirds.org . The webmasters reserve the right to edit and modify any submissions to this site. All material on this is site is copyrighted by the Squarebirds.org. Reproduction by any means other than for personal use is strictly prohibited. Permission to use material on this site can be obtained by contacting the webmasters. Copyright 2002-2016 by Squarebirds.org.