This will take you to the main site where there is history, technical information and other information on these cars.
This takes you back to the main page of the forums.
This is the control panel to change your password, information and preferences on this message board.
Click here if your lost your password or need to register on this message board. You must be a registered user to post. Registration is free.
Search this board for information you need.
Click here to buy cool Squarebirds mechandise.
Click here to support Squarebirds.org. For $20 annually receive 20mBytes webspace, a Squarebirds e-mail address and member's icon on the message board.
  #1  
Old 05-12-2014, 02:03 PM
DaveSouthampton DaveSouthampton is offline
Apprentice
 
Join Date: Nov 19 2013
Posts: 34
DaveSouthampton is on a distinguished road
Default Where to jack the car up from

I finally got my t-bird today

Now the fun really starts, along with lots more postings on here I suspect ... so sorry in advance.

My car has come with a jack. It looks correct and has the attachment for the back bumper at least. However I think I will be using a trolley jack as the bumper one just doesn't look that safe. I will of course be chocking it and potentially using axle stands too.

Where is it safe to put a jack underneath ? I will need to jack it to lift all 4 corners, or perhaps the front or rear etc.

Thanks again for all your help guys.
Reply With Quote
  #2  
Old 05-12-2014, 02:28 PM
YellowRose's Avatar
YellowRose YellowRose is offline
Super-Experienced and a HELLOFA nice guy
 
Join Date: Jan 21 2008
Posts: 12,681
YellowRose is on a distinguished road
Default Where to jack the car up from

Dave, I am going to let our terrific techies advise you as to where best to jack the car up. I will suggest this to you though. Whenever you have the car parked, pull the emergency brake on... These old Tbirds have been known to slip out of park and into gear. People have had their cars damaged by the car rolling back on them, damaging the garage door if it is down or partially down, or going down the driveway and into the street. So as a safety precaution, I ALWAYS pull the emergency brake on, when in Park and chock the wheels when I am working on the car. My driveway is also on a bit of an incline.
__________________

Ray Clark - Squarebirds Administrator
'59 Tbird "The Yellow Rose Of Texas" aka "Tweety Bird"
"It's Hip To Be Square"
Thunderbird Registry #33025 VTCI #11178

Contact me via Private Message for my email address, or (Cell) 210-875-1411 (Home) 210-674-5781
http://www.squarebirds.org/picture_gallery/TechnicalResourceLibrary/trl.htm
Reply With Quote
  #3  
Old 05-12-2014, 03:12 PM
DaveSouthampton DaveSouthampton is offline
Apprentice
 
Join Date: Nov 19 2013
Posts: 34
DaveSouthampton is on a distinguished road
Default

Hi Ray,

Thanks for that. Over here you fail your driving test if you don't use the hand brake, plus my old dad would bend my ear if I didn't put it on even at traffic lights lol.

I have to push it hard up into the P or it just clicks when I turn it over so I guess a steering column rebuild is on the horizon.

I too plan on making some nice wooden chocks... something like they used on WW1 biplanes
Reply With Quote
  #4  
Old 05-12-2014, 03:12 PM
jopizz's Avatar
jopizz jopizz is offline
Excellent Auto Mechanic for over 40 years.
 
Join Date: Nov 23 2009
Posts: 5,583
jopizz is on a distinguished road
Default

Here are the recommended body jacking points. Just be careful not to hit the brake and fuel lines.

John
Attached Images
File Type: jpg jacking.jpg (50.8 KB, 120 views)
__________________
John Pizzi - Squarebirds Administrator
1959 Convertible

Thunderbird Registry #36223
jopizz@verizon.net 856-779-9695

http://www.squarebirds.org/picture_gallery/TechnicalResourceLibrary/trl.htm
Reply With Quote
  #5  
Old 05-12-2014, 04:07 PM
Yadkin Yadkin is offline
Banned
 
Join Date: Aug 11 2012
Posts: 1,910
Yadkin is on a distinguished road
Default

Get yourself a good floor jack- Costco sells one of the best made for $100. Then some good jack stands. Cut blocks from 2x3 lumber to cushion the top of the stands.

Jack the front from the front cross member, the round one behind the radiator support. place the stands under the front torque boxes.

Jack the rear under the center of the differential. Place stands under the rear torque boxes.

Be aware that these cars are unit-chassis, and very rigid. So if you have a slight dip in your concrete floor the car will actually sit on three of the four stands.
Reply With Quote
  #6  
Old 05-12-2014, 08:23 PM
simplyconnected's Avatar
simplyconnected simplyconnected is offline
Slow Typist
 
Join Date: May 26 2009
Posts: 7,573
simplyconnected is on a distinguished road
Default

It's not a good idea to lift from the center of a differential. If the axle tubes are rusty, they will give out.

The only time I use a bumper jack is when NO other option is available. I use a two-ton floor jack or scissors jack. Bottle (hydraulic) jacks usually have a very small base, so I don't use them either.

Squarebirds have a unibody construction but they still have a front sub-frame and a rear sub-frame with two rocker channels in between. Look at your suspension. The front springs rest in the frame rails and the rear springs also attach to the frame. Use the frame to lift the car and put your jack stands under the frame. As an alternative, you may use the area just under the springs to jack up the car. Just make sure your jack cannot slip.

Whenever I pull an engine, do front suspension work or when I get under a car (any car) it will be on quality jack stands. Before getting under there, give the body a good shake like your life depends on it, because it does.

If the frame is in decent shape, I place my jack stands as far apart as practical to get the most stability. I call this area, 'the platform'. Think of an elephant standing on a small stool as opposed to him standing on four legs spread apart. Rollerbladers often widen their platform by leading one skate far ahead of the other, and they never fall.

Thunderbirds are very heavy. Respect that and always stay safe. Feel free to ask questions or to clarify the Shop Manual. - Dave
__________________
My latest project:
CLICK HERE to see my custom hydraulic roller 390 FE build.

"We've got to pause and ask ourselves: How much clean air do we need?"
--Lee Iacocca
Reply With Quote
  #7  
Old 05-13-2014, 08:42 AM
Yadkin Yadkin is offline
Banned
 
Join Date: Aug 11 2012
Posts: 1,910
Yadkin is on a distinguished road
Default

I'm assuming this car has a Ford 9" rear, which is heavy gauge all welded steel, legendary since it is basically unbreakable. Why wouldn't you jack the rear from it's center? If not there, where?
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -4. The time now is 02:16 PM.

Driving, racing or working on cars can be hazardous. The procedures and advice on this website including the message board are opinion only. Squarebirds.org and its webmasters and contributors do not guarantee the correctness of the advice and procedures. The Squarebirds.org and its webmasters assume no liability for any damage, fines, punishment, injury or death resulting from following these procedures or advice. If you do not have the skills or tools to repair your car, please consult a professional. By using this site you agree to hold harmless the Squarebirds.org, its authors and its webmasters from any resulting claim and costs that may occur from using the information found on this site.

Powered by vBulletin® Version 3.6.8
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
Any submissions to this site and any post on this site becomes property of Squarebirds.org . The webmasters reserve the right to edit and modify any submissions to this site. All material on this is site is copyrighted by the Squarebirds.org. Reproduction by any means other than for personal use is strictly prohibited. Permission to use material on this site can be obtained by contacting the webmasters. Copyright 2002-2016 by Squarebirds.org.