This will take you to the main site where there is history, technical information and other information on these cars.
This takes you back to the main page of the forums.
This is the control panel to change your password, information and preferences on this message board.
Click here if your lost your password or need to register on this message board. You must be a registered user to post. Registration is free.
Search this board for information you need.
Click here to buy cool Squarebirds mechandise.
Click here to support Squarebirds.org. For $20 annually receive 20mBytes webspace, a Squarebirds e-mail address and member's icon on the message board.
  #1  
Old 12-25-2014, 11:47 PM
Dan.loeb Dan.loeb is offline
Experienced
 
Join Date: Aug 2 2014
Posts: 105
Dan.loeb is on a distinguished road
Default Will this pcv system work?

Edelbrock valve covers with both valve covers with valve cover filters

Current open draft vent tube at rear of intake manifold routed to edelbrock 1406 with pcv valve between plugged into pcv port on carb?
Reply With Quote
  #2  
Old 12-26-2014, 02:45 AM
simplyconnected's Avatar
simplyconnected simplyconnected is offline
Slow Typist
 
Join Date: May 26 2009
Posts: 7,130
simplyconnected is on a distinguished road
Default

Dan the extraction depends on the amount of blowby you actually have. I don't mean to sound funny but if your draft tube billows smoke, no amount of vacuum will suck it back into your engine.

On an engine that has relatively low blowby, PCV works beautifully. If you have practically zero blowby, we don't want to suck gasses into the block. So now we have a balance between rocker breathers and blowby.

Vented rocker covers let fresh air in, to travel down the end oil holes in the heads and down to the oil pan. Blowby mixes with the fresh air and travels up the front of your block, around the timing chain and back into the valley (where the Positive Crankcase Valve is).

The mistake most people make is, they think PCV will end nasty crankcase smell in an engine too worn out.

Your setup sounds ok if you don't have too much for the PCV to handle. - Dave
__________________
My latest project:
CLICK HERE to see my custom hydraulic roller 390 FE build.

"We've got to pause and ask ourselves: How much clean air do we need?"
--Lee Iacocca
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -4. The time now is 02:35 PM.

Driving, racing or working on cars can be hazardous. The procedures and advice on this website including the message board are opinion only. Squarebirds.org and its webmasters and contributors do not guarantee the correctness of the advice and procedures. The Squarebirds.org and its webmasters assume no liability for any damage, fines, punishment, injury or death resulting from following these procedures or advice. If you do not have the skills or tools to repair your car, please consult a professional. By using this site you agree to hold harmless the Squarebirds.org, its authors and its webmasters from any resulting claim and costs that may occur from using the information found on this site.

Powered by vBulletin® Version 3.6.8
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Any submissions to this site and any post on this site becomes property of Squarebirds.org . The webmasters reserve the right to edit and modify any submissions to this site. All material on this is site is copyrighted by the Squarebirds.org. Reproduction by any means other than for personal use is strictly prohibited. Permission to use material on this site can be obtained by contacting the webmasters. Copyright 2002-2016 by Squarebirds.org.