This will take you to the main site where there is history, technical information and other information on these cars.
This takes you back to the main page of the forums.
This is the control panel to change your password, information and preferences on this message board.
Click here if your lost your password or need to register on this message board. You must be a registered user to post. Registration is free.
Search this board for information you need.
Click here to buy cool Squarebirds mechandise.
Click here to support Squarebirds.org. For $20 annually receive 20mBytes webspace, a Squarebirds e-mail address and member's icon on the message board.
  #1  
Old 09-26-2006, 08:41 PM
birdbrain birdbrain is offline
Experienced
 
Join Date: Jan 22 2005
Posts: 192
birdbrain is on a distinguished road
Default Head Gasket, burnt up revistied

As you all know, I had a problem with my car after running it with no water, All the while I was having problems with the high temp. Pulled the heads yesterday and found that the rear pistons on each side were clean as new. The head gasket was trickling water into the cylinders all the while.It did not start missing until recently, The block is in great shape and the heads are at the machine shop now being reworked. Both gaskets leaking at the rear what does this mean? That they were defective? The mechanic said it was an easy fix so I guess I will be riding again soon.;)
Reply With Quote
  #2  
Old 09-27-2006, 07:04 AM
JohnG's Avatar
JohnG JohnG is offline
John
 
Join Date: Jul 28 2003
Posts: 2,228
JohnG is on a distinguished road
Default RE: Head Gasket, burnt up revistied

The leaks occured due to the considerable temperature that the motor underwent while it had no coolant in it. All the parts possibly distorted and the seal between the gaskets and the two surfaces (block and heads) was broken, allowing water to work its way by. They had probably been doing a good job for tens of thousands of miles until that happened. With a little luck, the distortion went away when things cooled but the sealing ability of the gaskets was gone.


The questions you haven't addressed are whether the heads have been checked for flatness and cracks. Flatness would be check on a perfectly flat surface with a feeler gauge. The shop manual has the specs on what is unacceptable and requires planing. The cracks are revealed with "magnafluxing", a pretty standard procedure.

Make sure and use Fel-Pro head gaskets and intake gaskets so they don't have to be re-torqued.

While the heads are off perhaps think about replacing the seals on the valve guides? Easy and cheap to do now, hard later.
Reply With Quote
  #3  
Old 09-27-2006, 06:48 PM
birdbrain birdbrain is offline
Experienced
 
Join Date: Jan 22 2005
Posts: 192
birdbrain is on a distinguished road
Default RE: Head Gasket, burnt up revistied

Thanks john, The engine was rebuilt in December so it did not have 500 miles on it as of yet, I just left the machine shop that rebuilt the motor and they flow checked it, checked for cracks and made sure it was still true. They said everything thing was ok and yes I do have the felpro gaskets. The car should be back together tomoorw night. Since the season is over I am in no hurry. I am only sorry that I did such a thing, however there is a bright side to the story, the water passages in the rear of the block had some blockage due to the old radiator, they cleared that, now that I have a newly cored radiator with new heads and gaskets it will run just as good or better. My intake in the front and the back of the motor was leaking oil a steady small stream that's another reason I was glad to go back into the motor now it will be sealed up tight. I ordered one of those high voltage coils so I could gap my plugs wide, When I first got the car out the shop it ran like a bat out of hell now it will run that way again. now to carlise on friday for some new carpet! ;-)
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -4. The time now is 10:24 PM.

Driving, racing or working on cars can be hazardous. The procedures and advice on this website including the message board are opinion only. Squarebirds.org and its webmasters and contributors do not guarantee the correctness of the advice and procedures. The Squarebirds.org and its webmasters assume no liability for any damage, fines, punishment, injury or death resulting from following these procedures or advice. If you do not have the skills or tools to repair your car, please consult a professional. By using this site you agree to hold harmless the Squarebirds.org, its authors and its webmasters from any resulting claim and costs that may occur from using the information found on this site.

Powered by vBulletin® Version 3.6.8
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Any submissions to this site and any post on this site becomes property of Squarebirds.org . The webmasters reserve the right to edit and modify any submissions to this site. All material on this is site is copyrighted by the Squarebirds.org. Reproduction by any means other than for personal use is strictly prohibited. Permission to use material on this site can be obtained by contacting the webmasters. Copyright 2002-2016 by Squarebirds.org.