This will take you to the main site where there is history, technical information and other information on these cars.
This takes you back to the main page of the forums.
This is the control panel to change your password, information and preferences on this message board.
Click here if your lost your password or need to register on this message board. You must be a registered user to post. Registration is free.
Search this board for information you need.
Click here to buy cool Squarebirds mechandise.
Click here to support Squarebirds.org. For $20 annually receive 20mBytes webspace, a Squarebirds e-mail address and member's icon on the message board.
  #1  
Old 10-10-2012, 03:46 PM
Bill A Bill A is offline
Apprentice
 
Join Date: Jan 14 2012
Posts: 33
Bill A is on a distinguished road
Default Motorcraft 2100 carb adjustments

Hi to all. I have a Motorcraft 2100 carb on my 352. I believe its a 1963 vintage (someone did a swap in the past). The car runs well but I recently lowered the fast and hot idle rpm's. That went well but some of the choke adjustment specs are not given. I have the choke cover set properly but there is a screw behind the choke housing that positions the choke plate when engine is cold. The manual says to set it to specifications but I can't find any specs on that. Should there be a gap between the air-horn and the choke plate when you press on the gas pedal before stating? If so, how much? Or should the choke plate close tight at start-up (cold engine)?

Thanks,

Bill A
Reply With Quote
  #2  
Old 10-10-2012, 08:27 PM
Yadkin Yadkin is offline
Banned
 
Join Date: Aug 11 2012
Posts: 1,910
Yadkin is on a distinguished road
Default

Typically that gap is 1/8". Set it by using a drill bit held up against the vertical wall of the carb throat.
Reply With Quote
  #3  
Old 10-13-2012, 04:09 PM
Bill A Bill A is offline
Apprentice
 
Join Date: Jan 14 2012
Posts: 33
Bill A is on a distinguished road
Default Gap

Thanks for the info. If I remember correctly that was the gap I used for my 1969 390 2 BBL. For whatever reason I thought it would be tighter in this case. I'll try it and see if it makes a difference.

Regards,

Bill A
Reply With Quote
  #4  
Old 10-13-2012, 04:15 PM
jopizz's Avatar
jopizz jopizz is online now
Excellent Auto Mechanic for over 40 years.
 
Join Date: Nov 23 2009
Posts: 4,834
jopizz is on a distinguished road
Default

Normally with the choke set at the 1/8 inch spec the fast idle screw should be on the second highest lobe on the cam. There should be a circle or an arrow there.

John
__________________
John Pizzi - Squarebirds Administrator
1959 Convertible

Thunderbird Registry #36223
jopizz@verizon.net 856-779-9695

http://www.squarebirds.org/picture_gallery/TechnicalResourceLibrary/trl.htm
Reply With Quote
  #5  
Old 10-14-2012, 05:43 AM
KULTULZ
 
Posts: n/a
Post

I believe I have an original Spec Sheet for the 2100. I will try to dig it out MON and send it to YellowRose for posting.

Think of the 2100 as a 4100 without the secondary's.
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -4. The time now is 05:17 PM.

Driving, racing or working on cars can be hazardous. The procedures and advice on this website including the message board are opinion only. Squarebirds.org and its webmasters and contributors do not guarantee the correctness of the advice and procedures. The Squarebirds.org and its webmasters assume no liability for any damage, fines, punishment, injury or death resulting from following these procedures or advice. If you do not have the skills or tools to repair your car, please consult a professional. By using this site you agree to hold harmless the Squarebirds.org, its authors and its webmasters from any resulting claim and costs that may occur from using the information found on this site.

Powered by vBulletin® Version 3.6.8
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Any submissions to this site and any post on this site becomes property of Squarebirds.org . The webmasters reserve the right to edit and modify any submissions to this site. All material on this is site is copyrighted by the Squarebirds.org. Reproduction by any means other than for personal use is strictly prohibited. Permission to use material on this site can be obtained by contacting the webmasters. Copyright 2002-2016 by Squarebirds.org.