This will take you to the main site where there is history, technical information and other information on these cars.
This takes you back to the main page of the forums.
This is the control panel to change your password, information and preferences on this message board.
Click here if your lost your password or need to register on this message board. You must be a registered user to post. Registration is free.
Search this board for information you need.
Click here to buy cool Squarebirds mechandise.
Click here to support Squarebirds.org. For $20 annually receive 20mBytes webspace, a Squarebirds e-mail address and member's icon on the message board.
  #1  
Old 09-13-2011, 10:29 AM
kevin_tbird kevin_tbird is offline
Experienced
 
Join Date: Jun 12 2011
Posts: 157
kevin_tbird is on a distinguished road
Default Quarter Window Stop

I am reinstalling completely disassembled quarter windows. I have power windows.

I have all the diagrams. However, the stop that mounts to the window frame is hitting the regulator arm when the window moves up and down. I just can't figure out how it should install.

Advice please!!!

Kevin
Reply With Quote
  #2  
Old 09-13-2011, 01:51 PM
simplyconnected's Avatar
simplyconnected simplyconnected is offline
Slow Typist
 
Join Date: May 26 2009
Posts: 7,080
simplyconnected is on a distinguished road
Default

Kev, I know you have the illustrations, but could you tell us where the collision hits?
__________________
My latest project:
CLICK HERE to see my custom hydraulic roller 390 FE build.

"We've got to pause and ask ourselves: How much clean air do we need?"
--Lee Iacocca
Reply With Quote
  #3  
Old 09-14-2011, 07:58 AM
kevin_tbird kevin_tbird is offline
Experienced
 
Join Date: Jun 12 2011
Posts: 157
kevin_tbird is on a distinguished road
Default

part 29998 hits the regulator arm (which is part of the motor assembly)
Reply With Quote
  #4  
Old 09-15-2011, 08:54 AM
kevin_tbird kevin_tbird is offline
Experienced
 
Join Date: Jun 12 2011
Posts: 157
kevin_tbird is on a distinguished road
Default

I've included some photos. In the closeup of the arm/stop in the car the stop is removed, but you can see the holes. The window in the car is the drivers side. The one out of the car is the passenger side.

The regulator arm continues to sweep down (pic in car) as the sector gear moves and the arm hits the stop.

I must have this assembled wrong - but I do not see the answer. Top front of the window also does not go fully to the top and moves too far forward.

Please help. Only a couple days of vacation left this week and this is THE project keeping me off the road.

Thanks,
Kevin
Attached Images
File Type: jpg Q_wind_Stop.JPG (48.4 KB, 97 views)
File Type: jpg Q_wind_mech.JPG (89.7 KB, 96 views)
File Type: jpg Q_wind_stop_clr.JPG (40.6 KB, 95 views)
File Type: jpg Q_wind_install.JPG (20.4 KB, 94 views)
Reply With Quote
  #5  
Old 09-15-2011, 02:34 PM
partsetal's Avatar
partsetal partsetal is offline
Super-Experienced
 
Join Date: Jun 4 2005
Posts: 527
partsetal is on a distinguished road
Default

Kevin,
I see the problem now, but even tho I've worked with these many times, I've had this problem but don't recall how I worked thru it. I don't have an opened up quarter section to have a refresher look, but I'll pass on some observations. The arm in your photo of the right side laying down (3rd I believe) appears to have a depression in it. This could be from the camera position, but I'd first start with making sure the arms lay in a flat plane. I might even resort to adding a slight bend of my own to add some clearance. Since you say the window does not go up all the way and goes forward too far, you don't have the window adjusted properly, particularly the long bar that goes from the body at the bottom to the bottom of the window opening. I've spent more than a half a day trying to understand and get this adjustment to work.
How does it meet the rubber weather channel at the top? In or out here will alter how the arm clears the stop.
To summarize: Make sure the arms lay flat, and if possible put an outward curve (away from the window) in the offending arm; Adjust the window properly; Grind the stop to round the corner or remove any excess on the stop; persevere!
Good luck,
Carl
Reply With Quote
  #6  
Old 09-15-2011, 04:48 PM
Dakota Boy's Avatar
Dakota Boy Dakota Boy is offline
Super-Experienced
 
Join Date: Jun 30 2009
Posts: 1,498
Dakota Boy is on a distinguished road
Default

Its been a year and a half since I rebuilt my qtrs., but the "angle" of your motor on the drivers side just looks odd to me...

Are you sure you didnt flip flop the mechanisms to the wrong side of the car? but then maybe they wouldnt even bolt up if that was the case.
Reply With Quote
  #7  
Old 09-16-2011, 11:55 AM
GTE427's Avatar
GTE427 GTE427 is offline
Super-Experienced
 
Join Date: Oct 9 2007
Posts: 596
GTE427 is on a distinguished road
Default

I haven't taken apart and reassembled a rear quarter window myself, so I can't speak from experience. I've looked at the Ford Illustrations, your pictures and have added a cartoon diagram from Ford circa 1958 of a crank window assembly, realising your's is a power window setup.

When I compare your photos and the cartooned illustration, the window appears to be in the same position. Your photo clearly shows that the mechanism interferes with the upper window stop on the window frame, while the cartoon shows the mechanism is forward of the same stop.

If the cartoon can be trusted, it would seem the something isn't assembled correctly. On your drivers side, with the upper stop removed, do you have full range of travel from top to bottom of the window? I suggest you observe the travel of the window to see if there are any other interferences or problems with the operation. The roller assembly isn't install either (part # 23240), would this gain you any clearance when they are installed?

I hope this was of some help.
Attached Images
File Type: pdf rear window1.pdf (90.5 KB, 31 views)
__________________
Ken
1959 J Convertible
1960 J Hardtop

Last edited by GTE427 : 09-16-2011 at 12:04 PM.
Reply With Quote
  #8  
Old 09-16-2011, 12:43 PM
jopizz's Avatar
jopizz jopizz is offline
Excellent Auto Mechanic for over 40 years.
 
Join Date: Nov 23 2009
Posts: 4,756
jopizz is on a distinguished road
Default

Kevin,

Most of the binding problems are caused by the guide channel not being adjusted correctly. That's the one held in place by two bolts, part number 30244. I see yours is adjusted all the way up. Both of mine are almost all the way down. By the paint marks it looks like yours were originally all the way down too. That's also the reason your window goes too far forward. Everything looks assembled correctly.

John

Last edited by jopizz : 09-16-2011 at 12:46 PM.
Reply With Quote
  #9  
Old 09-16-2011, 01:17 PM
del's Avatar
del del is offline
Amateur Knuckle Buster
 
Join Date: May 11 2010
Posts: 207
del is on a distinguished road
Default

Kevin - Here are some photos of my left qtr window mechanism. I can take more or maybe answer some questions while I have the trim panel off - -let me know.
Attached Images
File Type: jpg TbirdLeftQtrWindow1.jpg (68.5 KB, 130 views)
File Type: jpg TbirdLeftQtrWindow2.jpg (68.4 KB, 130 views)
__________________
Regards,
Don Vincent
Amherst NY
1960 HT 352
TBird Registry 34042
Reply With Quote
  #10  
Old 09-17-2011, 07:37 AM
kevin_tbird kevin_tbird is offline
Experienced
 
Join Date: Jun 12 2011
Posts: 157
kevin_tbird is on a distinguished road
Default

Don -

Thanks for the photos. A couple of photos that would help are:

1. one that shows how the motor/regulator is mounted (which holes in the body).

2. one of the front window guide looking down from the top of the car. Part # 29752 in the diagram in the earlier post. Also a photo showing where the two adjusting bolts at the top of this part are aligned.

Don. I'm thinking that my problem is in how I have part 29752 installed. I need to adjust it up and back at the top, but am out of adjustment room. Thank you so much for helping.

regards, kevin
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -4. The time now is 11:48 AM.

Driving, racing or working on cars can be hazardous. The procedures and advice on this website including the message board are opinion only. Squarebirds.org and its webmasters and contributors do not guarantee the correctness of the advice and procedures. The Squarebirds.org and its webmasters assume no liability for any damage, fines, punishment, injury or death resulting from following these procedures or advice. If you do not have the skills or tools to repair your car, please consult a professional. By using this site you agree to hold harmless the Squarebirds.org, its authors and its webmasters from any resulting claim and costs that may occur from using the information found on this site.

Powered by vBulletin® Version 3.6.8
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Any submissions to this site and any post on this site becomes property of Squarebirds.org . The webmasters reserve the right to edit and modify any submissions to this site. All material on this is site is copyrighted by the Squarebirds.org. Reproduction by any means other than for personal use is strictly prohibited. Permission to use material on this site can be obtained by contacting the webmasters. Copyright 2002-2016 by Squarebirds.org.