This will take you to the main site where there is history, technical information and other information on these cars.
This takes you back to the main page of the forums.
This is the control panel to change your password, information and preferences on this message board.
Click here if your lost your password or need to register on this message board. You must be a registered user to post. Registration is free.
Search this board for information you need.
Click here to buy cool Squarebirds mechandise.
Click here to support Squarebirds.org. For $20 annually receive 20mBytes webspace, a Squarebirds e-mail address and member's icon on the message board.
  #1  
Old 08-27-2011, 07:54 AM
kuusamon's Avatar
kuusamon kuusamon is offline
Experienced
 
Join Date: Feb 14 2009
Posts: 305
kuusamon is on a distinguished road
Default problem joining FE, FMX and converter

Strange thing happened last night.
try to join the FMX gearbox (C9) with the 352 for my squarebird.
The bell housing is the aluminum one, and it did fit the engine before but with the Torque converter. No placing the torque converter in and joining them again it does not quite fit.
I can not tighten the bellhousing bolts all the way, just the last 1/4 inch or even less does not want to be tightened. The top 2 bolts of the bell housing can go all the way but the lower bolts not. When I tighten the bolts as much as I can than I can not turn the engine with the wrench on the crank pulley. When I back the bell housing off a bit then I can turn the engine.

I will take the gear box off again, I checked and the torque converter seems ok placed on the shaft.
I have put the converter on the gearbox when it was of the car, before just to check I put the converter and flex plate assembled together and also the the starter and all seemed ok.
The only mistake I made then is the I did not join it together with the 353 engine tot check.
Placed the engine, then after placed the gearbox without the converter.
No I was ready to insert the converter and then this happened.
Anybody has similar experiences?
I will have to take it apart again, check and write down the part numbers/casting numbers of the converter and flex plate and bell housing. I will post those numbers here shortly and see where did it go wrong.

When the gearbox was out of the car and assembled with the converter and flex plate and starter it seemed to fit perfectly.

When I purchased the car, the engine, bellhousing and gearbox came separately, they had never been joined together before.
I do have the original cast iron bell housing also but also has never been together also, it came as an extra part.

edit: the stamp on the converter shows 9B-4 or 9B-A ? and the number next to it is 56.
No number on the flexplate/flywheel only the fomoco stamp.

regards,
Ron
__________________
Greets,
Ronald
Kuusamo
http://www.tbirdregistry.com/viewdat...tryNumber=1741

Last edited by kuusamon : 08-27-2011 at 01:16 PM. Reason: new info
Reply With Quote
  #2  
Old 08-27-2011, 03:36 PM
kuusamon's Avatar
kuusamon kuusamon is offline
Experienced
 
Join Date: Feb 14 2009
Posts: 305
kuusamon is on a distinguished road
Default

Yes I found the answer I think
it must be the wrong converter. Taking trans engine matrimony apart and then fitting the converter on the flexplate, can get the 4 studs in place doesn't completely inserts in the pilot hole. The converter pilot is just about 1/8 inch too long.
Checking info on various websites came to that conclusion.
the pilot hole seems 2 stages first and biggest stage is 1.848 in diameter, second stage is 1.240 about.
The converter pilot is 1.375 in diameter of the stage that should fit in the 1.240 part.
Came to the conclusion is that the deeper stage pilot hole of 1.240 is not used but the first 1.848 is the important one so the converter pilot is just too long.
Which means the wrong converter type.
wonder if I could cut of 1/8 of an inch of the converter pilot.
Not thinking of widening the hole in the crankshaft pilot because it cause imbalance, maybe the same for the converter balance if I cut a piece off.

information website:
http://www.gopnh.com/Transmissions.c...mission=%20FMX

regards,
Ron
__________________
Greets,
Ronald
Kuusamo
http://www.tbirdregistry.com/viewdat...tryNumber=1741
Reply With Quote
  #3  
Old 08-28-2011, 04:26 AM
simplyconnected's Avatar
simplyconnected simplyconnected is offline
Slow Typist
 
Join Date: May 26 2009
Posts: 7,124
simplyconnected is on a distinguished road
Default

Ron, when I marry an engine to an automatic trans, I always build the flex plate to the crank, then I offer the torque converter and trans to the flex plate.

That's how the factory does it, too. After a couple wiggles, the four torque converter studs should slip right into the flex plate. Then the bell housing is tightened, and finally, the four converter nuts are installed. Rotating the starter gear to tighten the four nuts, seats the whole thing nicely.

There is really no such thing as a C10 or C9, they are just slang terms. Ford built C4's, C6's, then AOD's, etc.

You must find the right combination of flex plate, starter motor, and bell housing. The bell housing will determine which flex plate and torque converter will fit. Some engines use a 'sandwhich plate' between the engine and trans (like my 351W and AOD).

I have never run into your problem, where the torque converter pilot was too large for the crankshaft hole. I once had a converter that bloated so much, I could see imprints of the five crank bolts in the converter. Make sure there is no pilot bushing or bearing in the crankshaft (for a manual trans).

Good luck, Ron. - Dave
__________________
My latest project:
CLICK HERE to see my custom hydraulic roller 390 FE build.

"We've got to pause and ask ourselves: How much clean air do we need?"
--Lee Iacocca
Reply With Quote
  #4  
Old 08-28-2011, 05:24 AM
kuusamon's Avatar
kuusamon kuusamon is offline
Experienced
 
Join Date: Feb 14 2009
Posts: 305
kuusamon is on a distinguished road
Default

Thanks Dave,

yes remember my old thread from 2009:
http://squarebirds.org/vbulletin/sho...t=transmission

the gearbox casting number being C9ZP was standing for C9(FMX 1969) z= mustang and P= automatic.
by checking the right torque converter for it could not figure it out because my 'FMX' has 31 splines and there seems to be no FMX transmission and torque converter for it with 31 splines.
FMX has only 20 splines.
But my gearbox does have 31 splines so it must somehow be an overhauled gearbox with the 'wrong' casting code, the middle section being from a FMX.
But if I look for torque converters and the measurements then I came to the conclusion that it must be the C6 and not mentioned is the FMX name by those. all the measurements on the input drive shaft are correct for the C6, also the bell housing is correct.
The flex plate looks correct but no marking on it about a casting number.
The crank pilot hole looks like 2 stages but probably not used as 2 stages. the mane stage being 1.848 is correct for the C6 converter and also that converter has the shorter pilot.

I can probably answer my own question if I can shorten my pilot shaft on the converter I have now if the pilot shaft does not fit correctly, being smaller that the converter might be out of balance and vibrate. the pilot shaft with the correct fit makes sure that the (balanced) converter is exactly center, the studs just rotates the converter.
So if the converter is out of balance because of the wrong pilot shaft, the studs will just break.

Have to start looking for another torque converter.

The way I (tried to)installed it was exactly as you said, first the flexplate on the crank, the converter on the gearbox in the bell housing and line them up and 'marry' them. I did seem to go well with the exception of tightening the last 1/8 inch or so.
If I would have tried to put the converter on the flexplate before on the engine when the engine was out of the care I could have noticed it before but I didn't, I was so sure I had the right converter but I failed to do that.

regards,
ron
__________________
Greets,
Ronald
Kuusamo
http://www.tbirdregistry.com/viewdat...tryNumber=1741
Reply With Quote
  #5  
Old 08-28-2011, 06:45 AM
kuusamon's Avatar
kuusamon kuusamon is offline
Experienced
 
Join Date: Feb 14 2009
Posts: 305
kuusamon is on a distinguished road
Default

But you are right, there are no such thing as a c9 or c10, found that a casting number of C9 is very likely to be a FMX but doing the search couldn't find a FMX with a spline count of more than 29. info on the C6 type matching with a 352(390) and 31 splines was an easy match and gave the answers.

Anyway, trying to do anything perfect but failed to mount the trans on the engine before putting it in the car, just for trying out. paid for that dearly now with 2 extra days figuring it out.

I will 'marry' the trans with the engine now anyway but without the converter (who needs a converter anyway, lol) no just so I can continue, won't be ready to drive anyway until next summer. Have 2 or 3 weeks more work days on the car before I have to store it for the winter.
I can put the converter always in later. In this case I can make the rest of the car ready and hopefully start and run the engine without running the transmission.
My goal is before the winter storage to run the engine, make the brakes ready, normal and parking brake.
Also I got/ordered the wrong spark plug wires, had them on(ford racing red wires 9mm) from Summit, only to find out that they did not fit the distributor cap(original cap) because the distri. boots were HEI. considering either cutting them off and mount some boots that I can by locally or ordering new ones, the right ones this time.

regards,
Ron

hard to imagine, weather temperature still about 74F, leaves are already changing color and in another 4 or 5 weeks the first snow will fall.
I just heard that there will be likely another container from CA to Europe so I can do some more shopping and have the stuff and a correct converter maybe here by next spring, anybody has a converter laying around that they don't need?
__________________
Greets,
Ronald
Kuusamo
http://www.tbirdregistry.com/viewdat...tryNumber=1741

Last edited by kuusamon : 08-28-2011 at 07:45 AM.
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -4. The time now is 01:59 PM.

Driving, racing or working on cars can be hazardous. The procedures and advice on this website including the message board are opinion only. Squarebirds.org and its webmasters and contributors do not guarantee the correctness of the advice and procedures. The Squarebirds.org and its webmasters assume no liability for any damage, fines, punishment, injury or death resulting from following these procedures or advice. If you do not have the skills or tools to repair your car, please consult a professional. By using this site you agree to hold harmless the Squarebirds.org, its authors and its webmasters from any resulting claim and costs that may occur from using the information found on this site.

Powered by vBulletin® Version 3.6.8
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Any submissions to this site and any post on this site becomes property of Squarebirds.org . The webmasters reserve the right to edit and modify any submissions to this site. All material on this is site is copyrighted by the Squarebirds.org. Reproduction by any means other than for personal use is strictly prohibited. Permission to use material on this site can be obtained by contacting the webmasters. Copyright 2002-2016 by Squarebirds.org.