This will take you to the main site where there is history, technical information and other information on these cars.
This takes you back to the main page of the forums.
This is the control panel to change your password, information and preferences on this message board.
Click here if your lost your password or need to register on this message board. You must be a registered user to post. Registration is free.
Search this board for information you need.
Click here to buy cool Squarebirds mechandise.
Click here to support Squarebirds.org. For $20 annually receive 20mBytes webspace, a Squarebirds e-mail address and member's icon on the message board.
  #1  
Old 07-07-2010, 02:14 AM
gaffney1951 gaffney1951 is offline
Super-Experienced
 
Join Date: May 29 2007
Posts: 553
gaffney1951 is on a distinguished road
Default Alum. radiator install ...

Aluminum radiator install in 60' T-Bird ...

July 6 2010 at 10:03 PM Mike Gaffney Mike Gaffney (Login gaffney1951)
Members
Before pic.



The radiator is from Northern Auto, part# 209619. I chose the largest unit that would physically fit in the space available. It has two 1" rows and is a universal ford style. It ran $250 through my local radiator shop. I covered both sides of the core to prevent damage while taking measurements for fitment, and for sanding and polishing.



After mocking up fit I welded in the mounts I made from scrap I had around the shop.



The mounting surface at the top front of the rad. was originally bent upward and formed a channel with the one just to the rear of it. I bent it flat with a dead blow hammer in several passes back and forth. I added the rubber strip(some window seal I had, but self adhesive door weather strip would work just as well) to the rear one to help seal the shroud.


Here are pics of the A/C condenser and trans cooler with the top mounts in place. The bottum mounts are riveted in and are visible in the next shot. These again are made from scrap flat stock and the rubber pads are cut from garage door seal and contact cemented to the mounts, same for the rad. mounts.




Here you can see where I cut away part of the inner hood structure for radiator cap clearance (the old puke tank was eliminated) . I used modeling clay to check for clearance. Once I had sufficient clearance I cleaned up the opening painted inside and covered the opening edge with hood scoop rubber molding.




As there is tons of room at the firewall I added this combo rad. overflow/windshield washer resivoir.





There was originally a 3/4" raised flange at the bottom of the core support opening. I decided to cut this out and weld the seam shut to expose more of the rad. core to the air stream. Sorry no before shot.
[IMG]file:///Users/Michael/Library/Caches/TemporaryItems/moz-screenshot.png[/IMG]



Had to do some minor clearancing on the battery tray and reshape the A/C lines on both sides.



The rad. shroud was scavenged from a 79 LTD parts car I have. The width was perfect but required some trimming on the bottom and at the A/C compressor.



The original top rad. mount was retained and spacers were made to fit between the mount and the rad.. I used some lexan that I had in conjunction with a rubber bungee I cut to length for vibration dampening. This upgrade should almost double my cooling capacity and will hopefully eliminate any overheating issues when the stroker engine goes in in Nov.










Last edited by gaffney1951 : 07-08-2010 at 01:16 AM.
Reply With Quote
  #2  
Old 07-07-2010, 03:20 AM
YellowRose's Avatar
YellowRose YellowRose is offline
Super-Experienced and a HELLOFA nice guy
 
Join Date: Jan 21 2008
Posts: 11,897
YellowRose is on a distinguished road
Thumbs up Alum. radiator install ...

Excellent post, Mike! Great pix! Thanks for sharing this with us. I hope that JohnG will grab this and put it in the TRL for those in the future that might want to go this route with their Tbird.
__________________

Ray Clark - Squarebirds Administrator
'59 Tbird "The Yellow Rose Of Texas" aka "Tweety Bird"
"It's Hip To Be Square"
Thunderbird Registry #33025 VTCI #11178

rayclark07"at"att.net (Home) 210-674-5781 (Cell) 210-875-1411
http://www.squarebirds.org/picture_gallery/TechnicalResourceLibrary/trl.htm
Reply With Quote
  #3  
Old 07-07-2010, 07:04 PM
simplyconnected's Avatar
simplyconnected simplyconnected is offline
Slow Typist
 
Join Date: May 26 2009
Posts: 7,130
simplyconnected is on a distinguished road
Default

Well done, Mike! What a beautiful job on ALL your bracketry. - Dave
__________________
My latest project:
CLICK HERE to see my custom hydraulic roller 390 FE build.

"We've got to pause and ask ourselves: How much clean air do we need?"
--Lee Iacocca
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -4. The time now is 09:07 AM.

Driving, racing or working on cars can be hazardous. The procedures and advice on this website including the message board are opinion only. Squarebirds.org and its webmasters and contributors do not guarantee the correctness of the advice and procedures. The Squarebirds.org and its webmasters assume no liability for any damage, fines, punishment, injury or death resulting from following these procedures or advice. If you do not have the skills or tools to repair your car, please consult a professional. By using this site you agree to hold harmless the Squarebirds.org, its authors and its webmasters from any resulting claim and costs that may occur from using the information found on this site.

Powered by vBulletin® Version 3.6.8
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Any submissions to this site and any post on this site becomes property of Squarebirds.org . The webmasters reserve the right to edit and modify any submissions to this site. All material on this is site is copyrighted by the Squarebirds.org. Reproduction by any means other than for personal use is strictly prohibited. Permission to use material on this site can be obtained by contacting the webmasters. Copyright 2002-2016 by Squarebirds.org.