This will take you to the main site where there is history, technical information and other information on these cars.
This takes you back to the main page of the forums.
This is the control panel to change your password, information and preferences on this message board.
Click here if your lost your password or need to register on this message board. You must be a registered user to post. Registration is free.
Search this board for information you need.
Click here to buy cool Squarebirds mechandise.
Click here to support Squarebirds.org. For $20 annually receive 20mBytes webspace, a Squarebirds e-mail address and member's icon on the message board.
  #1  
Old 01-21-2017, 11:14 PM
deviot deviot is offline
Apprentice
 
Join Date: Aug 1 2013
Posts: 48
deviot is on a distinguished road
Default Freeze plug replacement

Hi,
Hi all,

I have a leaking freeze plug. As usual is the worst one, behind the engine mount.

I'm thinking my first attempt will be to move the engine forward, as it looks like if in undo everything it could move about 4".

Failing this I will take the engine out. Should I leave the bell housing attached and lift it out wth the engine?

Any suggestions would be appreciated.

Dave
__________________
Hello from Australia
Reply With Quote
  #2  
Old 01-23-2017, 12:30 PM
DKheld's Avatar
DKheld DKheld is offline
Super-Experienced
 
Join Date: Aug 27 2008
Posts: 1,434
DKheld is on a distinguished road
Default

Dave,










It is possible to do all the freeze plugs with the engine in the car. I had to remove the engine mounts and jack the engine up using a block under the oil pan as well as having the front tires removed and the car up on jack stands. Also had to remove the starter to get to the back one on that side.

It was not easy and I could not have done it without a freeze plug tool similar to this one but at least it is possible.



You are going to have such fun - might want to be sure the neighbors are not home - bad words will slip out.

Good luck....

Eric

Edit ...

On the engine removal (another problem) I just removed the engine and not the transmission. Bell housing will not separate from the transmission unless you have a different type than I do (perhaps a standard or straight drive tranny?)



Reply With Quote
  #3  
Old 01-23-2017, 03:53 PM
simplyconnected's Avatar
simplyconnected simplyconnected is offline
Slow Typist
 
Join Date: May 26 2009
Posts: 7,089
simplyconnected is on a distinguished road
Default

Quote:
Originally Posted by deviot View Post
...I have a leaking freeze plug. As usual is the worst one, behind the engine mount.
...
If one of your core plugs is bad, others are not far behind. Core plugs are inexpensive. Replace ALL of them with brass (commonly found in marine engines).

I've never used anything more than a hammer and a large flat-blade screwdriver to remove core plugs.



Keep the casting hole clean and free of scratches. Always use the core plug's inside recess to pound on so you don't mar the mating surface. For installation, I use s large socket and a hammer. - Dave
__________________
My latest project:
CLICK HERE to see my custom hydraulic roller 390 FE build.

"We've got to pause and ask ourselves: How much clean air do we need?"
--Lee Iacocca
Reply With Quote
  #4  
Old 01-23-2017, 09:51 PM
DKheld's Avatar
DKheld DKheld is offline
Super-Experienced
 
Join Date: Aug 27 2008
Posts: 1,434
DKheld is on a distinguished road
Default

X2 on the large socket Dave.

In this case there isn't much swinging room in the engine compartment with the engine installed so the long arm of the install tool gave you a place where you could whack away. Had to turn the wheels to clear the rotors and steering mechanism - back and forth - just find the sweet spot. Took a couple of evenings to - jack up the engine - remove the mounts, starter etc - remove the old plugs - clean the bores - then re-install the new plugs, mounts and set the engine back down.
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -4. The time now is 07:08 AM.

Driving, racing or working on cars can be hazardous. The procedures and advice on this website including the message board are opinion only. Squarebirds.org and its webmasters and contributors do not guarantee the correctness of the advice and procedures. The Squarebirds.org and its webmasters assume no liability for any damage, fines, punishment, injury or death resulting from following these procedures or advice. If you do not have the skills or tools to repair your car, please consult a professional. By using this site you agree to hold harmless the Squarebirds.org, its authors and its webmasters from any resulting claim and costs that may occur from using the information found on this site.

Powered by vBulletin® Version 3.6.8
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Any submissions to this site and any post on this site becomes property of Squarebirds.org . The webmasters reserve the right to edit and modify any submissions to this site. All material on this is site is copyrighted by the Squarebirds.org. Reproduction by any means other than for personal use is strictly prohibited. Permission to use material on this site can be obtained by contacting the webmasters. Copyright 2002-2016 by Squarebirds.org.