This will take you to the main site where there is history, technical information and other information on these cars.
This takes you back to the main page of the forums.
This is the control panel to change your password, information and preferences on this message board.
Click here if your lost your password or need to register on this message board. You must be a registered user to post. Registration is free.
Search this board for information you need.
Click here to buy cool Squarebirds mechandise.
Click here to support Squarebirds.org. For $20 annually receive 20mBytes webspace, a Squarebirds e-mail address and member's icon on the message board.
  #1  
Old 07-15-2016, 10:58 PM
Hazegray53 Hazegray53 is offline
Apprentice
 
Join Date: Jan 9 2015
Posts: 54
Hazegray53 is on a distinguished road
Default Pertronix 1.5 or 3 ohm coil

I bought a 3 ohm coil for my 60 sunliner with 352 not knowing that the instructions were going to tell me the 3 ohm is not recommended for V8's. So will the 3 ohm work or do I need to get the 1.5?
Reply With Quote
  #2  
Old 07-16-2016, 12:34 AM
simplyconnected's Avatar
simplyconnected simplyconnected is offline
Slow Typist
 
Join Date: May 26 2009
Posts: 7,159
simplyconnected is on a distinguished road
Default

The only function Pertronix performs is to short your coil to ground when spark should happen. Your points did exactly the same thing, but mechanically. Also, Pertronix uses no condenser.

Pertronix offers their own coils with different internal resistance called, 'Flame throwers', that should be used with a properly sized ballast resistor (if any at all). (Call Pertronix for ballast sizing.)

You can use your OEM coil and ballast resistor BUT make sure your Pertronix unit is fed with NON-resistor wire that comes from +12 volts (on the red wire to your distributor). - Dave
__________________
My latest project:
CLICK HERE to see my custom hydraulic roller 390 FE build.

"We've got to pause and ask ourselves: How much clean air do we need?"
--Lee Iacocca
Reply With Quote
  #3  
Old 07-16-2016, 12:55 AM
Hazegray53 Hazegray53 is offline
Apprentice
 
Join Date: Jan 9 2015
Posts: 54
Hazegray53 is on a distinguished road
Default

I have the flamethrower 3 ohm coil. Will it work properly when I bypass the resistance wire or do I need the flamethrower 1.5 ohm coil?
Reply With Quote
  #4  
Old 07-16-2016, 01:27 AM
simplyconnected's Avatar
simplyconnected simplyconnected is offline
Slow Typist
 
Join Date: May 26 2009
Posts: 7,159
simplyconnected is on a distinguished road
Default

Your shop manual says the OEM coil has a primary resistance of:
1.4-1.54 ohms.

It also says your OEM ballast resistor should measure:
1.3-1.4 ohms.

If the Flame Thrower is a 1.5 ohm coil, it is the same as your original coil and it will work well with your original ballast resistor.

For proper ballast resistance on the 3 ohm Flame Thrower, call Pertronix. To me, it looks suspiciously like an 'internal resistance' coil because if I add the OEM ballast resistance and the OEM coil resistance, I come up with about three ohms. - Dave
__________________
My latest project:
CLICK HERE to see my custom hydraulic roller 390 FE build.

"We've got to pause and ask ourselves: How much clean air do we need?"
--Lee Iacocca
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -4. The time now is 07:02 AM.

Driving, racing or working on cars can be hazardous. The procedures and advice on this website including the message board are opinion only. Squarebirds.org and its webmasters and contributors do not guarantee the correctness of the advice and procedures. The Squarebirds.org and its webmasters assume no liability for any damage, fines, punishment, injury or death resulting from following these procedures or advice. If you do not have the skills or tools to repair your car, please consult a professional. By using this site you agree to hold harmless the Squarebirds.org, its authors and its webmasters from any resulting claim and costs that may occur from using the information found on this site.

Powered by vBulletin® Version 3.6.8
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Any submissions to this site and any post on this site becomes property of Squarebirds.org . The webmasters reserve the right to edit and modify any submissions to this site. All material on this is site is copyrighted by the Squarebirds.org. Reproduction by any means other than for personal use is strictly prohibited. Permission to use material on this site can be obtained by contacting the webmasters. Copyright 2002-2016 by Squarebirds.org.