This will take you to the main site where there is history, technical information and other information on these cars.
This takes you back to the main page of the forums.
This is the control panel to change your password, information and preferences on this message board.
Click here if your lost your password or need to register on this message board. You must be a registered user to post. Registration is free.
Search this board for information you need.
Click here to buy cool Squarebirds mechandise.
Click here to support Squarebirds.org. For $20 annually receive 20mBytes webspace, a Squarebirds e-mail address and member's icon on the message board.
  #1  
Old 05-28-2016, 05:31 PM
Hazegray53 Hazegray53 is offline
Apprentice
 
Join Date: Jan 9 2015
Posts: 54
Hazegray53 is on a distinguished road
Default Intake manifold install

I can't seem to get all the bolts on this intake to go in smoothly at the same time. It's either one side or the other. The front 2 seem to be the most out of alignement. Back story is my 1960 352 block was cracked. It already had 61 heads on it with the 60 intake. So I ended up with a 62 block, using the same heads with valve job and the same intake. Should these all fit together or am I just doing it wrong?
Reply With Quote
  #2  
Old 05-28-2016, 06:54 PM
jopizz's Avatar
jopizz jopizz is offline
Excellent Auto Mechanic for over 40 years.
 
Join Date: Nov 23 2009
Posts: 4,842
jopizz is on a distinguished road
Default

Yes, the manifold should bolt up to your '61 heads and '62 block. Measure the bolt holes in the heads across the front and across the back. If they don't measure the same then something is off. If they measure the same then check that your intake gaskets are in the right spot. If they slide down the manifold won't sit right. It has to fit so you have something amiss.

John
__________________
John Pizzi - Squarebirds Administrator
1959 Convertible

Thunderbird Registry #36223
jopizz@verizon.net 856-779-9695

http://www.squarebirds.org/picture_gallery/TechnicalResourceLibrary/trl.htm
Reply With Quote
  #3  
Old 05-28-2016, 07:08 PM
jopizz's Avatar
jopizz jopizz is offline
Excellent Auto Mechanic for over 40 years.
 
Join Date: Nov 23 2009
Posts: 4,842
jopizz is on a distinguished road
Default

Also make sure that the hole in the intake where the dowel pin goes is clear and not blocked.

John
__________________
John Pizzi - Squarebirds Administrator
1959 Convertible

Thunderbird Registry #36223
jopizz@verizon.net 856-779-9695

http://www.squarebirds.org/picture_gallery/TechnicalResourceLibrary/trl.htm
Reply With Quote
  #4  
Old 05-28-2016, 08:11 PM
Hazegray53 Hazegray53 is offline
Apprentice
 
Join Date: Jan 9 2015
Posts: 54
Hazegray53 is on a distinguished road
Default

Thanks guys! After the complete failure yesterday I got all the sealant cleaned up and spent a few hours worth of dry runs to figure out how to get everything lined up. Well it's finally in! Definitely more difficult than I thought it would be and I was using a lift. I basically had to keep just enough tension on the lift so it was easy enough to move a little while I was putting in each bolt.
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -4. The time now is 03:30 AM.

Driving, racing or working on cars can be hazardous. The procedures and advice on this website including the message board are opinion only. Squarebirds.org and its webmasters and contributors do not guarantee the correctness of the advice and procedures. The Squarebirds.org and its webmasters assume no liability for any damage, fines, punishment, injury or death resulting from following these procedures or advice. If you do not have the skills or tools to repair your car, please consult a professional. By using this site you agree to hold harmless the Squarebirds.org, its authors and its webmasters from any resulting claim and costs that may occur from using the information found on this site.

Powered by vBulletin® Version 3.6.8
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Any submissions to this site and any post on this site becomes property of Squarebirds.org . The webmasters reserve the right to edit and modify any submissions to this site. All material on this is site is copyrighted by the Squarebirds.org. Reproduction by any means other than for personal use is strictly prohibited. Permission to use material on this site can be obtained by contacting the webmasters. Copyright 2002-2016 by Squarebirds.org.