This will take you to the main site where there is history, technical information and other information on these cars.
This takes you back to the main page of the forums.
This is the control panel to change your password, information and preferences on this message board.
Click here if your lost your password or need to register on this message board. You must be a registered user to post. Registration is free.
Search this board for information you need.
Click here to buy cool Squarebirds mechandise.
Click here to support Squarebirds.org. For $20 annually receive 20mBytes webspace, a Squarebirds e-mail address and member's icon on the message board.
  #1  
Old 12-07-2002, 10:59 AM
1960Bird 1960Bird is offline
Experienced
 
Join Date: Dec 4 2002
Posts: 159
1960Bird is on a distinguished road
Default Shift linkage

My shift lever is very loose and to get the car into drive I have to pull the lever down to the low gear setting. Is there an easy fix for this problem.
__________________
390, Mild Cam, Headers, 3.70 rear, 2-1/2" Exhaust, Edelbrok Performer RPM Intake, Holley Street Avenger 670 Carburetor, One Wire Alt, Petronix Ignition. She's All Go and No Show.
Reply With Quote
  #2  
Old 12-07-2002, 12:00 PM
Alexander's Avatar
Alexander Alexander is offline
Webmaster
 
Join Date: Oct 30 2002
Posts: 3,338
Alexander is on a distinguished road
Default RE: Shift linkage

The usual areas of most wear for the shift linkage is in the shift collar and the working end of the shift lever. You will probably notice that the holes for the shift lever roll pin in the shift collar are oblong rather than the round roll pin diameter it is supposed to be. The working end of the shift lever is rounded instead of square after years of use.

The good news is that both the shift collar and the shift lever are now reproduced. The shift collar B7228A costs about $100. I am not sure how much the lever costs.

I had the same problem in my 1959. Unfortunately there were no repro pieces at the time. I epoxied in a hollow rivet in the shift collar to make it round again. I had to buy a NOS piece for the shift lever - not cheap.The alternative to buying a whole shift lever is welding metal onto the rounded edges and then filing them square. You will need to know the shpe of the original lever end for this. I have seen a lot of worn levers. It is amazing how much wears away on some.

Alexander
1959 Hardtop
1960 Golde Top

__________________
Alexander
1959 Hard Top
1960 Golde Top
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -4. The time now is 06:57 PM.

Driving, racing or working on cars can be hazardous. The procedures and advice on this website including the message board are opinion only. Squarebirds.org and its webmasters and contributors do not guarantee the correctness of the advice and procedures. The Squarebirds.org and its webmasters assume no liability for any damage, fines, punishment, injury or death resulting from following these procedures or advice. If you do not have the skills or tools to repair your car, please consult a professional. By using this site you agree to hold harmless the Squarebirds.org, its authors and its webmasters from any resulting claim and costs that may occur from using the information found on this site.

Powered by vBulletin® Version 3.6.8
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Any submissions to this site and any post on this site becomes property of Squarebirds.org . The webmasters reserve the right to edit and modify any submissions to this site. All material on this is site is copyrighted by the Squarebirds.org. Reproduction by any means other than for personal use is strictly prohibited. Permission to use material on this site can be obtained by contacting the webmasters. Copyright 2002-2016 by Squarebirds.org.