This will take you to the main site where there is history, technical information and other information on these cars.
This takes you back to the main page of the forums.
This is the control panel to change your password, information and preferences on this message board.
Click here if your lost your password or need to register on this message board. You must be a registered user to post. Registration is free.
Search this board for information you need.
Click here to buy cool Squarebirds mechandise.
Click here to support Squarebirds.org. For $20 annually receive 20mBytes webspace, a Squarebirds e-mail address and member's icon on the message board.
  #1  
Old 07-12-2005, 10:43 PM
dgs's Avatar
dgs dgs is offline
Super-Experienced
 
Join Date: Feb 13 2003
Posts: 921
dgs is on a distinguished road
Default Front end special tools and lube

I have my deluxe front end kit and shocks on order from Kanter and I've been perusing the shop manual to see what I'm in for. I've got a few questions:[ul][li]The manual lists a Ball Joint Removal Tool #T57P-3006-A as needed to take the ball joints out. Is this special tool really needed? If so, where do I get one? If not, how do I get the ball joints out without it?[/li][li]Will I need to have a machine shop press the control arm bushings in and out, or is there a means of doing that without a press? I seem to remember someone saying they had done so.[/li][li]For the stabilizer mounts and shock absorber mounts, it calls for RyGLYDE lubricant. What should I use there?[/li][li]The manual shows using a floor jack to release the spring pressure and to re-install it. It makes no mention of a spring compressor tool. Has anyone done it that way? Those coil springs are pretty intimidating to me.[/li][/ul]I might have more questions as I get into it, I'll let you know. :-P In the mean time, if anyone has any other pointers they learned along the way, please fill me in.
__________________
DGS (aka salguod)
1960 Convertible - Raven Black, Red leather
www.salguod.net
Reply With Quote
  #2  
Old 07-12-2005, 11:28 PM
dgs's Avatar
dgs dgs is offline
Super-Experienced
 
Join Date: Feb 13 2003
Posts: 921
dgs is on a distinguished road
Default RE: Front end special tools and lube

OK, I just re-found the tips and suggestions in [a href="http://www.squarebirds.org/dcforum/DCForumID1/512.html"]this thread[/a], but it didn't answer my question about the lube and the ball joint tool.
__________________
DGS (aka salguod)
1960 Convertible - Raven Black, Red leather
www.salguod.net
Reply With Quote
  #3  
Old 07-13-2005, 09:30 AM
bobs58 bobs58 is offline
Experienced
 
Join Date: May 5 2005
Posts: 156
bobs58
Default RE: Front end special tools and lube

What I did was remove the cotter pin on one ball joint and then loosened the retaining nut several turns but did not remove it. For the upper nut, I first removed the bolt that holds the backing plate to the spindle to gain access for a socket over the ball joint nut. Using the coil spring to keep tension on the whole system, I used a fork shaped tool (can buy or rent at auto parts store) and a 5 pound sledge hammer (NOT a regular hammer-not enough mass) and the wedge in the fork seperated the parts after a few good wacks. You can "feel" the parts seperate as the spring pushes the parts apart. I then did the same operation on the other ball joint. Jack up the lower control arm, loosen both nuts, bleed down the jack, and remove the spring as per the shop manual. Removing the rivets for the ball joints is a job for an air chisel. If you do it by hand, you might finish by Christmas.
Reply With Quote
  #4  
Old 07-13-2005, 10:09 AM
dgs's Avatar
dgs dgs is offline
Super-Experienced
 
Join Date: Feb 13 2003
Posts: 921
dgs is on a distinguished road
Default RE: Front end special tools and lube

Thanks Bob. I doubt my ball joints are still riveted, the car has 150,000 miles on it. Surely they've been replaced at least once! If they are still riveted, I might start thinking that maybe it really is only 50,000 miles instead of 150,000.

Another question: Did you pull the entire suspention apart at once? I'm thinking that I'll do lower arms, stabilizer bar and steering stuff first and leave the upper arms in place. Then put the lowers back together and tackle the uppers. That way I won't have to remove the spindles. Is that worth it, or is it easier to just pull everything, including spindles, at once?
__________________
DGS (aka salguod)
1960 Convertible - Raven Black, Red leather
www.salguod.net
Reply With Quote
  #5  
Old 07-13-2005, 12:17 PM
Alexander's Avatar
Alexander Alexander is offline
Webmaster
 
Join Date: Oct 30 2002
Posts: 3,338
Alexander is on a distinguished road
Default RE: Front end special tools and lube

Instead of RyGLYDE, you can use silicone lubricant(not the glue).

Alexander
1959 Hardtop
1960 Golde Top
__________________
Alexander
1959 Hard Top
1960 Golde Top
Reply With Quote
  #6  
Old 07-13-2005, 12:28 PM
bobs58 bobs58 is offline
Experienced
 
Join Date: May 5 2005
Posts: 156
bobs58
Default RE: Front end special tools and lube

I removed the spindle with all the various brake parts.

1. I replaced the rubber brake hose (probably as old as the car) and it was much easier to get at the wheel cylinder end on a bench rather than try to fit a wrench in tight quarters under the car.
2. I made the decision to pay a shop to press out and press in all the bushings so I brought them all 4 control arms at the same time and saved a trip. They charged me $60 and it was money I gladly spent to press out/in 16 bushings.

If you us jackstands to raise the car, I would suggest that you get the car as high as safely possible for best access. The lower control arm needs to clear the floor once it is loosened and hanging down. You will have to roll the floor jack from the opposite side and under the engine to later compress the spring in the lower control arm as you reassemble the suspension. I personally found it easier to first install the spindle to the LOWER ball joint stud (hand tighten nut), jack up the control arm and then guide the upper ball joint into the spindle slot as the coil spring is compressed. Since the upper control arm bushing nuts have not yet been torqued down, it is easily moved up and down to align the stud. The new ball joints are very tight and I had to use a piece of pipe over the stud to move it so it was aligned correctly.

Been there, done that. Good luck. By the way, I used some of that new liquid spray-on bandaid stuff. It works great to stop bleeding but it BURNS LIKE THE DEVIL for several seconds.
Reply With Quote
  #7  
Old 07-13-2005, 06:00 PM
dgs's Avatar
dgs dgs is offline
Super-Experienced
 
Join Date: Feb 13 2003
Posts: 921
dgs is on a distinguished road
Default RE: Front end special tools and lube

I went through the brakes two years ago, rebuilt wheel cylinders, rebuilt master cylinder, new rubber lines, etc. I was trying to avoid opening up the brake lines and having to re-pack the wheel bearings. We'll see how it goes. The fun begins tonight as I get the car off the ground and start taking things off.

Thanks for the reminder of those ball joint forks. I've changed the lower ball joints on my 1993 Escort twice and 'rented' those from Autozone. Forgot all about that tool.
__________________
DGS (aka salguod)
1960 Convertible - Raven Black, Red leather
www.salguod.net
Reply With Quote
  #8  
Old 06-10-2016, 07:42 PM
GeoffInCarlsbad's Avatar
GeoffInCarlsbad GeoffInCarlsbad is offline
Experienced
 
Join Date: Jul 4 2015
Posts: 187
GeoffInCarlsbad is on a distinguished road
Default Will this work for a '61?

Quote:
Originally Posted by bobs58 View Post
What I did was remove the cotter pin on one ball joint and then loosened the retaining nut several turns but did not remove it. For the upper nut, I first removed the bolt that holds the backing plate to the spindle to gain access for a socket over the ball joint nut. Using the coil spring to keep tension on the whole system, I used a fork shaped tool (can buy or rent at auto parts store) and a 5 pound sledge hammer (NOT a regular hammer-not enough mass) and the wedge in the fork seperated the parts after a few good wacks. You can "feel" the parts seperate as the spring pushes the parts apart. I then did the same operation on the other ball joint. Jack up the lower control arm, loosen both nuts, bleed down the jack, and remove the spring as per the shop manual. Removing the rivets for the ball joints is a job for an air chisel. If you do it by hand, you might finish by Christmas.
Hi Bob (or any other experienced person may want to chime in):

I found this quote when looking for info in the T57P-3006 tool for Ball Joint Removal. I see how you describe that you used a Pickle Fork and a 5-lb sledge to pop out the (lower?) ball joint from the Lower Control Arm.

I had recently put in new Upper & Lower L&R Ball Joints, but for some reason failed to replace the LCA Bushing at the Frame.

So now I need to do that, but don't want to damage the lower ball joint that I just put in last July.

Will your fork & sledge method damage the ball joint or the boot?

Have you any pictures that show how you did this that you could share?
__________________
Geoff In Carlsbad
1961 Thunderbird Convertible
2008 F-250 Super Duty Diesel Long Bed
Reply With Quote
  #9  
Old 06-12-2016, 08:38 AM
OX1 OX1 is offline
Experienced
 
Join Date: Feb 10 2016
Posts: 255
OX1 is on a distinguished road
Default

Take two 1/2 inch high grade bolts. Screw them together with a coupling nut. Remove both ball joint nuts, reinsert upside down and screw in until they are flush with end of ball joint stud.

Place bolts and coupling setup between ball joint/ball joint nuts and screw them out to create pressure on both ball joints (forcing them apart). Hammer side of knuckle near the ball joint stud you want to release, should pop out.

The other ball joint will require press or tool. recommend this tool.

Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -4. The time now is 03:16 AM.

Driving, racing or working on cars can be hazardous. The procedures and advice on this website including the message board are opinion only. Squarebirds.org and its webmasters and contributors do not guarantee the correctness of the advice and procedures. The Squarebirds.org and its webmasters assume no liability for any damage, fines, punishment, injury or death resulting from following these procedures or advice. If you do not have the skills or tools to repair your car, please consult a professional. By using this site you agree to hold harmless the Squarebirds.org, its authors and its webmasters from any resulting claim and costs that may occur from using the information found on this site.

Powered by vBulletin® Version 3.6.8
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Any submissions to this site and any post on this site becomes property of Squarebirds.org . The webmasters reserve the right to edit and modify any submissions to this site. All material on this is site is copyrighted by the Squarebirds.org. Reproduction by any means other than for personal use is strictly prohibited. Permission to use material on this site can be obtained by contacting the webmasters. Copyright 2002-2016 by Squarebirds.org.