This will take you to the main site where there is history, technical information and other information on these cars.
This takes you back to the main page of the forums.
This is the control panel to change your password, information and preferences on this message board.
Click here if your lost your password or need to register on this message board. You must be a registered user to post. Registration is free.
Search this board for information you need.
Click here to buy cool Squarebirds mechandise.
Click here to support Squarebirds.org. For $20 annually receive 20mBytes webspace, a Squarebirds e-mail address and member's icon on the message board.
  #1  
Old 02-10-2008, 04:29 AM
prglasbergen's Avatar
prglasbergen prglasbergen is offline
Newbie
 
Join Date: Jan 3 2008
Posts: 5
prglasbergen is on a distinguished road
Exclamation Refurbish ram steering cylinder

Can anyone tell me how to refurbish the ram steering cilinder of a 1960 ford thunderbird?? I have the cilinder and the new parts, but i am unable to open the cilinder, does anyone have a good discription or some images?? Help is higly appriciated
Reply With Quote
  #2  
Old 02-10-2008, 11:41 AM
Dan Leavens's Avatar
Dan Leavens Dan Leavens is offline
Moderator / Administrator
 
Join Date: Oct 4 2006
Posts: 4,503
Dan Leavens is on a distinguished road
Wink

Peter, to help you with your cylinder question do the following.

On the main forum page up in the right hand corner you will see " search " button. Hit it and then type in "steering cylinder". Once open, you will see a variety of posts to this subject. If you open you will see the posts and replies 11.27.07 by 6TBird ( George ) hopefully that will answer some questions
If not, then send 6TBird an e-mail and he can help you out.

Dano Calgary,Alberta Canada
Reply With Quote
  #3  
Old 02-12-2008, 09:18 PM
6TB1RD's Avatar
6TB1RD 6TB1RD is offline
Experienced
 
Join Date: Apr 9 2006
Posts: 382
6TB1RD is on a distinguished road
Thumbs up

Peter:

Sorry it took so long to get to you on this, I haven't gotten on the form to much since my auto accident I was hit in the passenger door of my truck and it was totaled, so I'm slow getting to the posts.

(I hope we are talking about the power cylinder Passenger side 2lines.) If not let me know and I will send you the info on the control cylinder.

1. When you remove the ram cylinder from the car the easiest way to do it will be turn the wheel all the way left this extends the cylinder all the way out remove the nut on the end of the rod. And the 2 hydro lines,

2 using compressed air (I forget witch hole) I look at it this way we have a 50-50 chance of getting it right on the first try.
The air will retract the cylinder in to the housing

3. Undo the nut holding the cylinder to the steering bars, and remove from the car.

4. Using a bench vice if you have one makes the rest of the job easer. Mount the cylinder in the vice using soft jaws, or rap it with 2 or so raps of a shop towel. Do not clamp it to tight or you will damage the cylinder.

5. Using snap ring pliers looking at the rod end of the cylinder remove the lock ring from the end. Hold a rag over the end and using compress air to the same port that you used to retract the rod this will force the seal and backing ring out of the end of the cylinder. If it does not come out the first time, put air to the other port it took me about three cycles back and forth to get the seal out.

6. Clean and inspect the rod and end of the cylinder for damage if none. Then reinstall the seal and backing.

If your kit was like mine you will not use all parts in the kit. So look at the way the seal comes out and match them with the new seals and install the new seal with lots of tyranny fluid to make sure the seal goes in right. You may have to use a socket the size of the cylinder opening to seat the seal (I did) but tap lightly so the seal will not be damaged.

"Only put in the same number of parts you took out”

Reinstall the snap ring making sure it gets in to the groove in the cylinder.

Push and pull the rod in and out by hand wile doing so put a finger over one of the holes the rod will either stop or get hard to move and when you let go it will move slightly in the opposite direction. This means the end sealed up properly. And you’re ready to reinstall.

(One quick thing when you put the power steering system back together make sure you have some one to help one to turn the wheel back and forth and one to add the tyranny fluid, you will notice the level drop quick fast when you first turn the wheel and you can run the pump dry) I know this from experience!

Power steering pumps are not fun to rebuild.
__________________
George (Papa of 9)
1960 H/T :rolleyes:
Home Page http://squarebirds.org/users/6tb1rd/
http://www.tbirdregistry.com/viewdat...ryNumber=31811
Reply With Quote
  #4  
Old 02-13-2008, 08:55 AM
6TB1RD's Avatar
6TB1RD 6TB1RD is offline
Experienced
 
Join Date: Apr 9 2006
Posts: 382
6TB1RD is on a distinguished road
Exclamation I forgot something read with caution

2 A)using compressed air (I forget witch hole) I look at it this way we have a 50-50 chance of getting it right on the first try.
The air will retract the cylinder in to the housing


2B) TRY TO MOVE THE ROD BY HAND FIRST IF IT WILL NOT MOVE THEN USE THE COMPRESSESD AIR BUT WATCH OUT FOR THE FLUID COMMING OUT THE OTHER HOLE
__________________
George (Papa of 9)
1960 H/T :rolleyes:
Home Page http://squarebirds.org/users/6tb1rd/
http://www.tbirdregistry.com/viewdat...ryNumber=31811
Reply With Quote
  #5  
Old 02-14-2008, 03:25 AM
prglasbergen's Avatar
prglasbergen prglasbergen is offline
Newbie
 
Join Date: Jan 3 2008
Posts: 5
prglasbergen is on a distinguished road
Thumbs up Re: Refurbish ram steering cylinder

Hey 6Tb1rd,

Thnx a lot for this info, , will try to fix this saturday, I'll let you know how it turned out. Will make pictures and post them so others can be helped too,

Peter
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -4. The time now is 05:47 AM.

Driving, racing or working on cars can be hazardous. The procedures and advice on this website including the message board are opinion only. Squarebirds.org and its webmasters and contributors do not guarantee the correctness of the advice and procedures. The Squarebirds.org and its webmasters assume no liability for any damage, fines, punishment, injury or death resulting from following these procedures or advice. If you do not have the skills or tools to repair your car, please consult a professional. By using this site you agree to hold harmless the Squarebirds.org, its authors and its webmasters from any resulting claim and costs that may occur from using the information found on this site.

Powered by vBulletin® Version 3.6.8
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Any submissions to this site and any post on this site becomes property of Squarebirds.org . The webmasters reserve the right to edit and modify any submissions to this site. All material on this is site is copyrighted by the Squarebirds.org. Reproduction by any means other than for personal use is strictly prohibited. Permission to use material on this site can be obtained by contacting the webmasters. Copyright 2002-2016 by Squarebirds.org.