This will take you to the main site where there is history, technical information and other information on these cars.
This takes you back to the main page of the forums.
This is the control panel to change your password, information and preferences on this message board.
Click here if your lost your password or need to register on this message board. You must be a registered user to post. Registration is free.
Search this board for information you need.
Click here to buy cool Squarebirds mechandise.
Click here to support For $20 annually receive 20mBytes webspace, a Squarebirds e-mail address and member's icon on the message board.
Old 07-20-2017, 07:59 AM
Wyldie's Avatar
Wyldie Wyldie is offline
Join Date: Dec 22 2016
Posts: 76
Wyldie is on a distinguished road
Default Engine options

G'day guys

Will start a thread soon on the bird, been hard at it since I got it 3 weeks ago! All going well, couple of suprises along the way, more on that later.

Ran the numbers on the engine it has a 352 59-60 block in it. Measured the bore once I got the heads off. The engine had been taken to 4.050 stroke is still 3.5" so looks to be taken to around 390ci.

Cylinder 6 however has a broken ring which has damaged the bore. Just my luck! Anywho hoping someone can tell me what's the maximum I can bore the block to? What are my options?
Reply With Quote
Old 07-20-2017, 11:05 AM
pbf777 pbf777 is offline
Join Date: Jan 9 2016
Posts: 240
pbf777 is on a distinguished road

Originally Posted by Wyldie
Cylinder 6 however has a broken ring which has damaged the bore. Just my luck! Anywho hoping someone can tell me what's the maximum I can bore the block to? What are my options?
Unfortunately, the question of what the maximum amount of material, that can be remove to achieve a required bore diameter with in a particular block, and maintaining a reasonable service life, isn't so simple to answer accurately.

I am of the general opinion that the highly educated and therefore well paid engineers were tasked with the responsibility of creating a product (engine block) that would provide acceptable service life, under the environmental conditions in which outlined, and maintaining costs of manufacturing to a minimum. With these parameters in mind, add the fact that the FE engine was of Ford's newly announced "Thin-Wall-Casting" technique, and the understanding that Ford Motor Company wants to sell new vehicles, not have you rebuilding your old one; why would anyone assume that there is any additional, unnecessary material (iron) added, over and above that required to keep the vehicle out of warranty claims and allow the targeted cycle life by the manufacturer?

Does this mean one can't bore a block to an oversize in the rebuilding process, no, it is practiced; but remember, all things practiced, even if it "works", are not always necessarily correct. I believe this allowance is due to the engineers consideration for manufacturing tolerances and given inaccuracies. Such variables exist in the metallurgy, pouring and casting technique, finish machining, etc.; these considerations cause the addition of materials in order to reduce rejections.

I believe the best advice is to always remove the minimal sum of material from the cylinder walls as possible for best results.

In a more direct answer to your question, if the damage (scoring) in the cylinder will not "clean-up" in reasonable honing, then one would advise a repair sleeve installation process.

"Reasonable Honing", well your block has already been bored .050" oversize (what is required for the other cylinders?); I suppose one could explore out to .060" (check for ring availability), but that's where I would draw the line. And I didn't say that such is an acceptable "maximum", it's just often practiced.

Reply With Quote
Old 07-20-2017, 02:27 PM
simplyconnected's Avatar
simplyconnected simplyconnected is offline
Slow Typist
Join Date: May 26 2009
Posts: 7,521
simplyconnected is on a distinguished road

We use a sonic test to determine how much wall is left.

It is ideal to remove the minimum diameter of metal from your bores but that's not the only consideration. I had my Y-block bored +.060" because that was the closest size piston that was available at the time.

So the question is, who will stock all pistons in all sizes and how many sets will they keep on hand? The pistons are cast in batches, then the machining is set up in 'production runs'. They make thousands at a time. When a specific size is depleted, the next run may take a while because NONE of this stock is paid for until it is actually sold.

Alright, having said all that hot air, let's get more practical. If you're already +.050" you're at the end of your rope. Ten thousandths more is only FIVE thousandths per side. That's twice the thickness of a human hair; hardly enough to 'clean up' deep scratches.

I would look for a common 390 short block, either from a pickup truck or a car. If it needs a +.030" bore, so be it. There's plenty of casting left. - Dave
My latest project:
CLICK HERE to see my custom hydraulic roller 390 FE build.

"We've got to pause and ask ourselves: How much clean air do we need?"
--Lee Iacocca
Reply With Quote
Old 07-20-2017, 06:22 PM
Wyldie's Avatar
Wyldie Wyldie is offline
Join Date: Dec 22 2016
Posts: 76
Wyldie is on a distinguished road

All interesting, unfortunately a new block is out of the question. They are not readily available in Australia, they didn't come standard in anything we have.

Looks like I'll take the block to an engine rebuilder, see if I can get number 6 sleeved, see what my options are. If that can't be done then ummm... Might have to concider moving to a 351 small block. But I really want to keep a big block in it
Reply With Quote

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

All times are GMT -4. The time now is 02:12 AM.

Driving, racing or working on cars can be hazardous. The procedures and advice on this website including the message board are opinion only. and its webmasters and contributors do not guarantee the correctness of the advice and procedures. The and its webmasters assume no liability for any damage, fines, punishment, injury or death resulting from following these procedures or advice. If you do not have the skills or tools to repair your car, please consult a professional. By using this site you agree to hold harmless the, its authors and its webmasters from any resulting claim and costs that may occur from using the information found on this site.

Powered by vBulletin® Version 3.6.8
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
Any submissions to this site and any post on this site becomes property of . The webmasters reserve the right to edit and modify any submissions to this site. All material on this is site is copyrighted by the Reproduction by any means other than for personal use is strictly prohibited. Permission to use material on this site can be obtained by contacting the webmasters. Copyright 2002-2016 by