This will take you to the main site where there is history, technical information and other information on these cars.
This takes you back to the main page of the forums.
This is the control panel to change your password, information and preferences on this message board.
Click here if your lost your password or need to register on this message board. You must be a registered user to post. Registration is free.
Search this board for information you need.
Click here to buy cool Squarebirds mechandise.
Click here to support Squarebirds.org. For $20 annually receive 20mBytes webspace, a Squarebirds e-mail address and member's icon on the message board.
  #1  
Old 07-07-2017, 11:23 AM
p38fighter p38fighter is offline
Apprentice
 
Join Date: Oct 14 2016
Posts: 55
p38fighter is on a distinguished road
Default Roping in a windshield - bottom or top?

1959 convertible

I have put in a few windshields - mostly on 55/57 Chevys. The wings of the Chevy are smaller than the TBird's. I am concerned about the corners because of that fact. The shop manual says start from the top of the glass but I'm wondering what practical experience people have had? Did you pull in the top or the bottom first? If the bottom was there any particular reason?

Thanks as always for the advice....
Reply With Quote
  #2  
Old 07-07-2017, 11:42 AM
Joe Johnston Joe Johnston is online now
Super-Experienced
 
Join Date: Dec 23 2008
Posts: 670
Joe Johnston is on a distinguished road
Default

I've always pulled in the bottom first. Just seemed easier to hold everything together with the weight of the windshield sitting on the lip to get started. Pushing down is easier than trying to push up also. Just my opinion.

I use insulated electrical wire because it seems the plastic insulation will slip and lift the gasket easier than rope because it is slippery and smaller diameter. Either works however.
Reply With Quote
  #3  
Old 07-07-2017, 01:13 PM
simplyconnected's Avatar
simplyconnected simplyconnected is offline
Slow Typist
 
Join Date: May 26 2009
Posts: 7,159
simplyconnected is on a distinguished road
Default

I used to watch the guys on the assembly line install windshields. Two guys worked together. One guy was half in and half out of the car as he reached in and grabbed both ends of the rope. He jerked the rope in a rhythmic tempo while both slapped vibrations on opposite sides of the glass from the outside.

The rope came vulcanized into the weatherstrip so it didn't come out very easy and no lubrication was used. You can imagine, as the rope was jerked, it became long in the guy's hand. That's why he jerked it out in 'bites'. Then, I noticed a box full of spent ropes.

At a rate of 1,000 windshields per day (one per minute), they sent the used ropes back to be re-vulcanized in new weatherstrips. Each rope had splotches of black on the surface; evidence of little pieces of the many weatherstrips from whence they came.

If memory serves me, I believe the ropes started at the top. Of course all their actions were meticulously orchestrated but it seemed to me that their slapping actions were the most important in seating the glass in the weatherstrip and in the aperture of the car body. These weren't little love taps and every once in a great while a windshield would crack, especially when they weren't in unison. - Dave
__________________
My latest project:
CLICK HERE to see my custom hydraulic roller 390 FE build.

"We've got to pause and ask ourselves: How much clean air do we need?"
--Lee Iacocca
Reply With Quote
  #4  
Old 07-10-2017, 08:00 PM
p38fighter p38fighter is offline
Apprentice
 
Join Date: Oct 14 2016
Posts: 55
p38fighter is on a distinguished road
Default Successful installation

1959 convertible

My son and I put in the windshield. Decided to start at the center bottom and let gravity help. It took about 15 minutes start to finish. We only had to apply some judicious slapping to the driver side top corner to get it to seat. I found the lip slipped easiest when I pulled the rope at 90 degrees to the gasket and kept my hand close to the window. I used soapy water for a lubricant.

In my opinion this is a job that can be handled by two careful people.
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -4. The time now is 06:40 PM.

Driving, racing or working on cars can be hazardous. The procedures and advice on this website including the message board are opinion only. Squarebirds.org and its webmasters and contributors do not guarantee the correctness of the advice and procedures. The Squarebirds.org and its webmasters assume no liability for any damage, fines, punishment, injury or death resulting from following these procedures or advice. If you do not have the skills or tools to repair your car, please consult a professional. By using this site you agree to hold harmless the Squarebirds.org, its authors and its webmasters from any resulting claim and costs that may occur from using the information found on this site.

Powered by vBulletin® Version 3.6.8
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Any submissions to this site and any post on this site becomes property of Squarebirds.org . The webmasters reserve the right to edit and modify any submissions to this site. All material on this is site is copyrighted by the Squarebirds.org. Reproduction by any means other than for personal use is strictly prohibited. Permission to use material on this site can be obtained by contacting the webmasters. Copyright 2002-2016 by Squarebirds.org.