This will take you to the main site where there is history, technical information and other information on these cars.
This takes you back to the main page of the forums.
This is the control panel to change your password, information and preferences on this message board.
Click here if your lost your password or need to register on this message board. You must be a registered user to post. Registration is free.
Search this board for information you need.
Click here to buy cool Squarebirds mechandise.
Click here to support Squarebirds.org. For $20 annually receive 20mBytes webspace, a Squarebirds e-mail address and member's icon on the message board.
  #1  
Old 06-21-2015, 11:02 AM
ramos291 ramos291 is offline
Apprentice
 
Join Date: Sep 18 2014
Posts: 66
ramos291 is on a distinguished road
Default Idler Arm confusion MFG date 11/61

There seems to be a lot of slop/play in the idler arm. I replaced the bushing but the slop/play is still there. Enough play that my alignment shop is unable to do an alignment. What options are there to fix this slop? The bushing is new and suppose to be for the correct MFG date. The mechanic thought maybe the bracket shaft is worn. Replacement of the whole assembly is pricey and i have seen postings of using a 64's assembly. Is there some one that just has the bracket shaft assembly (mounts to the frame)?
Reply With Quote
  #2  
Old 06-21-2015, 02:21 PM
simplyconnected's Avatar
simplyconnected simplyconnected is online now
Slow Typist
 
Join Date: May 26 2009
Posts: 7,080
simplyconnected is on a distinguished road
Default

The same arm was used from '61-'63. Many of the vendors have this part but it isn't cheap:


Personally, I would remove the bottom parts and carefully inspect the shaft. Then I would consider a repair job instead of spending hundreds on a new one.

I don't know how you feel about 'originality' but you could probably switch to rack and pinion for about the same money. All the slop would be gone and the new system uses fewer joints because there is no counter-shaft. - Dave
__________________
My latest project:
CLICK HERE to see my custom hydraulic roller 390 FE build.

"We've got to pause and ask ourselves: How much clean air do we need?"
--Lee Iacocca
Reply With Quote
  #3  
Old 06-21-2015, 09:43 PM
Ian M Greer's Avatar
Ian M Greer Ian M Greer is offline
Experienced
 
Join Date: Jul 29 2010
Posts: 143
Ian M Greer is on a distinguished road
Default

I actual fact there was a difference between bushing diameters from 61/62 dating before 4/4/61 to 3/15/62 sized at 2 7/16 inches long by 5/8 I.D by 19/32 outside diameter. and the later from 3/15/62 which in the Bible is mentioned as ( Upper - 2.312 inches long by .76 ID. The very early 61 before 4/4/61 was a 2.6 inch long and by .63 I. D. bushing . Make sure you have the right bushing (if your going concours , you of coarse want the right one ) Many of the vendors will sell you a replacement design using the heavier made 64 idler arm and bushing set-up which they say is better as the originals were made too thin and weak . Ian
Reply With Quote
  #4  
Old 11-26-2015, 02:29 PM
Jerry Forrester Jerry Forrester is offline
Newbie
 
Join Date: Nov 2 2015
Posts: 3
Jerry Forrester is on a distinguished road
Default

The idler arm bushing was worn out on my '62. Dec. '61 build date. I ordered the early bushing from Birdnest. It came in and I attempted to install it. The ID was too small to fit on the shaft. I ordered the later one with the larger ID and everything worked out perfect.
Anybody need a '61-early 62 idler arm bushing?
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -4. The time now is 06:03 AM.

Driving, racing or working on cars can be hazardous. The procedures and advice on this website including the message board are opinion only. Squarebirds.org and its webmasters and contributors do not guarantee the correctness of the advice and procedures. The Squarebirds.org and its webmasters assume no liability for any damage, fines, punishment, injury or death resulting from following these procedures or advice. If you do not have the skills or tools to repair your car, please consult a professional. By using this site you agree to hold harmless the Squarebirds.org, its authors and its webmasters from any resulting claim and costs that may occur from using the information found on this site.

Powered by vBulletin® Version 3.6.8
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Any submissions to this site and any post on this site becomes property of Squarebirds.org . The webmasters reserve the right to edit and modify any submissions to this site. All material on this is site is copyrighted by the Squarebirds.org. Reproduction by any means other than for personal use is strictly prohibited. Permission to use material on this site can be obtained by contacting the webmasters. Copyright 2002-2016 by Squarebirds.org.