Squarebirds, Rocketbirds, and Fifties/Sixties Ford Discussion Forum

Squarebirds, Rocketbirds, and Fifties/Sixties Ford Discussion Forum (http://squarebirds.org/vbulletin/index.php)
-   1958 To 1960 Squarebirds - General Technical Discussion (http://squarebirds.org/vbulletin/forumdisplay.php?f=14)
-   -   Gear Selection (http://squarebirds.org/vbulletin/showthread.php?t=9364)

howelljason70 08-02-2010 03:25 PM

Gear Selection
 
For some reason my transmission will not shift into low. I removed the linkage from the column and manually moved the transmission shift linkage and there are only five selections. When I am driving if i try and shift into low it will downshift to first but it does not actually stay in the low selection. Once I have tried to engage low it will stay in first gear through out the rpm range. I then have to select d2 to get it to shift into second. Has anyone had any experience this or is this how a Cruise-O-Matic from a 1959 should behave? Thanks

KULTULZ 08-02-2010 04:36 PM



Dan Leavens 08-02-2010 06:19 PM

Gary thanks for the post and answer on the cruise-o-matic operation. Ray perhaps we can pick this thread up and place Gary's post in our technical section...

Jason: If it helps, with the driving speed and amount of miles we put on our 58 & 60 they are always in D2. The others may chime in as well, as to their driving habits.

howelljason70 08-02-2010 07:14 PM

Thank you guys very much for the replies. Well with a lot of tinkering, adjustment of the linkage and adjustment of the detent plate, I was able to correct the problem. I now have all of the gear selections in working order.

howelljason70 08-02-2010 07:17 PM

Throttle to Transmission Linkage
 
Does anyone by any chance happen to have a picture of their throttle to transmission linkage where the adjustment point is. I have a feeling mine is a bit off, it is almost all the way adjusted out. Thanks again!

YellowRose 08-02-2010 07:48 PM

Gear Selection
 
I have already grabbed the pix and will grab the thread for the TRL. It is good information. Me, I drive in D1, which is what I was told we should drive in. That is what those instructions say also, for normal driving..

Richard D. Hord 08-02-2010 07:53 PM

4 Attachment(s)
Hey Jason,
Here's some I took don't know if they will help or not!
Richard D. Hord

howelljason70 08-02-2010 08:14 PM

Awesome! Those images are exactly what I was looking for. Thanks a bunch! Time to go do some comparison and see if I can make some positive changes.

Dakota Boy 08-02-2010 10:13 PM

howelljason70,

You will find the group here to be helpful beyond belief.

This is truly one of the best boards out there.

YellowRose 08-02-2010 11:24 PM

Gear Selection
 
Hi Greg,

Thank you for that comment! It is much appreciated! We, your administrators, webmaster, and moderators are trying to do Alexander proud... Our fellow members on here are certainly helping us do that!

Richard, I have grabbed those great pix of the linkage for the TRL. More than likely this thread will end up there also. Thanks!

KULTULZ 08-03-2010 12:55 AM

These trannys are pre-modulator valve (introduced in 1961) and the shifts are actually controlled by the fuel/kickdown linkages as is an AOD (TV ADJ. ROD).

The procedure(s) for adjusting the linkage(s) are in your shop manual.

Good job on finding you had a selector/adjustment problem.

If all of the linkage(s) are now tight, make sure the engine/trans mounts are good to prevent unwanted cradle movement. This will also bind the linkage(s).

KULTULZ 08-03-2010 01:39 AM

That Gearshift Selector Description is from a 1960 FORD Owners Manual.

Here's that pesky Trans Pressure Test Port that i have been unable to verify as of yet-



Here is the using of a pressure gauge on a TWIN-TURBO of the period to arrive at proper TV pressure-


GTE427 08-03-2010 07:16 AM

Gary,

What are you looking for regarding the test port? I have a 59 Lincoln SB that states the last 500 Lincolns would have this line installed for use on the assembly line, thus adjustment at the dealer most likely wouldn't be needed. I don't recall seeing a similar one for Fords.

Let me know if I can help.

Paulie9fingers 08-03-2010 02:28 PM

. . my '60 has the test port too

KULTULZ 08-04-2010 02:32 AM

Quote:

Originally Posted by GTE427 (Post 47856)

Gary,

What are you looking for regarding the test port? I have a 59 Lincoln SB that states the last 500 Lincolns would have this line installed for use on the assembly line, thus adjustment at the dealer most likely wouldn't be needed. I don't recall seeing a similar one for Fords.

Let me know if I can help.

...sheesh...

I made a reply post earlier today and somehow must have reviewed it and forgot to actually post it...

There has been a question here for some time what this port was. I had remembered reading somewheres that it was a test port for assembly line verification of AT pressure.

I found the TSB you referenced (THANX!) but am positive I also saw it in either FORD or BIRD reference material.

Thanx again for the reference, I have been vindicated... :)


All times are GMT -4. The time now is 12:09 AM.

Powered by vBulletin® Version 3.6.8
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Any submissions to this site and any post on this site becomes property of Squarebirds.org . The webmasters reserve the right to edit and modify any submissions to this site. All material on this is site is copyrighted by the Squarebirds.org. Reproduction by any means other than for personal use is strictly prohibited. Permission to use material on this site can be obtained by contacting the webmasters. Copyright 2002-2016 by Squarebirds.org.