Squarebirds, Rocketbirds, and Fifties/Sixties Ford Discussion Forum

Squarebirds, Rocketbirds, and Fifties/Sixties Ford Discussion Forum (http://squarebirds.org/vbulletin/index.php)
-   1961 To 1963 Bulletbirds, Rocketbirds - General Technical Discussion (http://squarebirds.org/vbulletin/forumdisplay.php?f=24)
-   -   speedometer help ... (http://squarebirds.org/vbulletin/showthread.php?t=21310)

cervantes1m 02-20-2017 12:12 AM

speedometer help ...
 
3 Attachment(s)
Hello,

Fellow members I hope I can get some help.

Over the weekend I replaced the speedometer cable and speedometer gear because my speed gauge needle would bounce back and forth then it just stopped working.

When i removed the old cable i found that it had broken and also the gear was not in such good shape.

Replaced with new parts took my baby out for a drive, it worked great for couple of miles and then it stopped working.

I double checked my connections at the transmission and speedometer and found nothing.

I then checked the actual speedometer and noticed that the port were the speedo cable goes into looked stripped.

is that part replaceable or anyone recommend a place to have it repaired.

Yadkin 02-20-2017 09:13 AM

Read this thread and see if your problems might be the same as mine (the odometer stuck).

http://www.squarebirds.org/vbulletin...4906#post94906

cervantes1m 02-20-2017 12:22 PM

@YADKIN.....thank you unfortunately that is not my problem.

jopizz 02-20-2017 02:45 PM

I would check with the vendors that sell used parts like The Birds Nest, The Thunderbird Connection or Pat Wilson Thunderbirds and see if you can get a good used speedometer or the gear housing. To my knowledge that part is not available new.

John

cervantes1m 02-20-2017 04:07 PM

@JOPIZZ thank you ....

simplyconnected 02-20-2017 07:16 PM

I've never heard of a speedometer cable wearing out the brass socket. That socket should spin freely with NO resistance. I hope you can perform work on your bench, not in the dash.

Many replacement cables were 'cut to length' with a plastic end, which seemed to work without complaints. Normally, when a speedometer cable breaks, it is because it wore into the shield in one place and it created a snag. So, I always bought the complete assembly for replacement.

Back to your 'washed-out' square. Determine if your speedometer moves freely. You may use a drill motor to test, but read on. If your new cable came with a nylon end, this is a piece of cake... You can clean the hole and use epoxy.

Before you freak out, the hole should be 'lacquer thinner clean' so epoxy sticks well. Some folks swear by JB Weld, but any good epoxy will work. Use a toothpick to apply in the hole covering all the sides and some on the bottom. Put a thin coat of grease on the cable end before you stick it in the epoxy hole. Epoxy will not stick to grease. Keep it straight and clean off any excess immediately. Your new cable should slide in and out with slight pressure after curing, if you do it right. - Dave

cervantes1m 02-21-2017 11:09 AM

Thank you Dave.....ill keep you posted


All times are GMT -4. The time now is 05:56 AM.

Powered by vBulletin® Version 3.6.8
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Any submissions to this site and any post on this site becomes property of Squarebirds.org . The webmasters reserve the right to edit and modify any submissions to this site. All material on this is site is copyrighted by the Squarebirds.org. Reproduction by any means other than for personal use is strictly prohibited. Permission to use material on this site can be obtained by contacting the webmasters. Copyright 2002-2016 by Squarebirds.org.