Squarebirds, Rocketbirds, and Fifties/Sixties Ford Discussion Forum

Squarebirds, Rocketbirds, and Fifties/Sixties Ford Discussion Forum (http://squarebirds.org/vbulletin/index.php)
-   1957 To 1969 Full Size Fords - General Technical Discussion (http://squarebirds.org/vbulletin/forumdisplay.php?f=23)
-   -   MBM Brake Booster Master Combo (http://squarebirds.org/vbulletin/showthread.php?t=20198)

Hazegray53 03-06-2016 03:50 PM

MBM Brake Booster Master Combo
 
I have the MBM brake booster kit PBUF5772 for my 60 Sunliner and I'm having trouble fitting the firewall bracket to the booster itself.
Here is a photo of the complete kit.



In the next two photos I'm trying to show that the bracket won't mount to the booster with the threaded push rod centered. When connected it just pulls the rod down and way off center. It looks like it would work if the threaded rod was much shorter. Is it supposed to be adjustable? Am I supposed to cut it to fit? What am I doing wrong here?




simplyconnected 03-07-2016 01:39 AM

Quote:

Originally Posted by Hazegray53 (Post 99001)
...When connected it just pulls the rod down and way off center. It looks like it would work if the threaded rod was much shorter. Is it supposed to be adjustable? Am I supposed to cut it to fit? ...

Yes, and I'm surprised they didn't tell you in the instructions. I like your pictures but I need to see how long your clevis (eyelet) is. Show one with a scale next to it.

Leave the jam nut on but back it off as far as you can. Hold the clevis (eyelet) up to it and eyeball where you want to cut the booster rod.

If it builds your confidence to cut a little at a time, ok. By the time you get close, the distance will be the same.

Use the jam nut to 'chase' the end of the thread once it's cut.

It's very important you bench bleed your M/C before mounting it. Did they supply a plastic bench bleed kit? I mount my M/C on my vise and use a #4 Phillips screwdriver in the hole as I progressively stroke the piston. Start with short, slow strokes then as the bubbles come out go deeper. After about twenty times, the bubbles will stop.

I don't like the 'closed ports' method. - Dave

Hazegray53 03-07-2016 09:58 PM

The only instructions I could find were on the MBM site. Those instructions assume you already have everything put together. They do provide a bench bleed kit. I was just trying to get everything mounted for fitment. I'm sure I'll probably have to make some brake lines also. The clevis is 1 1/2". Here's the pic.
Looks to me like I'll have to cut quite a bit of the booster rod for it to be centered when connected. The clevis will be right up against the boot.


simplyconnected 03-07-2016 10:37 PM

Yep, that's ok and that's how mine is. I have the same clevis you do, the short 1-1/2" version. They offer a longer one, but you already have the correct clevis.

Go ahead and start cutting... - Dave

Hazegray53 03-07-2016 10:59 PM

Ok will do. I'll let you know how it goes. What's the best way to mount the combination valve?

simplyconnected 03-07-2016 11:20 PM

The best way is to mount the combination valve on your fender apron, then pipe to it. That gets it out of the way when you work on you engine or spark plugs.

I liken this to your electrical and plumbing components in your house.. Mount the fixtures and boxes FIRST, then wire or pipe to them. - Dave

Hazegray53 03-11-2016 09:43 PM

Here are a couple pics of it mounted up. The clevis is right up against the firewall but I don't think its applying any pressure. I think it will be ok? by the time I cut the pushrod so it would fit like this, there was no more room for a jam nut.




Joe Johnston 03-11-2016 10:13 PM

Not real keen about it touching or the lack of a jam nut. Why not add a spacer and move it forward? Plenty of length on the mounting studs.

simplyconnected 03-12-2016 03:45 AM

Nice job, and neatly tucked in. Spacers or big washers behind the booster would be ok but really not necessary. Our Galaxie is the same. The booster rod cannot turn and neither can the clevis. Make sure your hardware is tight. Any flexing turns into 'soft brake pedal'. - Dave


All times are GMT -4. The time now is 10:00 AM.

Powered by vBulletin® Version 3.6.8
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Any submissions to this site and any post on this site becomes property of Squarebirds.org . The webmasters reserve the right to edit and modify any submissions to this site. All material on this is site is copyrighted by the Squarebirds.org. Reproduction by any means other than for personal use is strictly prohibited. Permission to use material on this site can be obtained by contacting the webmasters. Copyright 2002-2016 by Squarebirds.org.