Squarebirds, Rocketbirds, and Fifties/Sixties Ford Discussion Forum

Squarebirds, Rocketbirds, and Fifties/Sixties Ford Discussion Forum (http://squarebirds.org/vbulletin/index.php)
-   1958 To 1960 Squarebirds - General Technical Discussion (http://squarebirds.org/vbulletin/forumdisplay.php?f=14)
-   -   Leaky oil breather cap (http://squarebirds.org/vbulletin/showthread.php?t=17977)

1960_tbirdman 11-21-2014 03:24 PM

Leaky oil breather cap
 
This past weekend, after 20 miles of highway driving, there seems to be oil coming from the breather cap. This never happened before. I recently did the PCV valve conversion using a spacer plate under the carburetor but did not change the original oil breather cap. I had driven it on the streets with no issues until this weekend. I saw some past postings about this but did not understand the messages posted as to what the problem may be. Thanks for any assistance.

simplyconnected 11-21-2014 04:34 PM

How bad is your blowby? PCV is great IF it sucks out more fumes than are being created by the piston blowby.

How many breathers do you have?

What route does your blowby take?

1960_tbirdman 11-21-2014 05:04 PM

Before the PCV valve conversion, you could see the smoke coming from hood at stop. It also came in through center vent during driving but we discovered hole in A/C housing while doing the conversion.

I have one breather cap, looks original. I now have oil that seems to be coming from cap and runs along valve cover,

Joe Johnston 11-21-2014 05:16 PM

Any chance of the new PCV installed backwards? They act like a check valve and only flow one way - easy to do if its the type installed in a hose, but most can't be done backwards as one end fits in a grommet.

Spacer plate under the carb? Could you have connected the hose to the fitting for a water passage? (I'm only familiar with Bullet Birds and they have a water passage in their spacer. Perhaps 58-60's don't?)

Posting a couple of pictures will help.

DKheld 11-21-2014 07:00 PM

x2 with Joe

When I was installing mine I found that there are a coupe of different types of spacers. The first one I bought drew air from the secondaries when installed on my carb so the only time it worked was when you opened it up. Also the spacers can be installed upside down - don't ask how I know - :o

If you have a vacuum gauge see if you have any vacuum at the inlet. I'm guessing no and since you don't have a road draft tube any longer it's pushing all the fumes out the breather.

Eric

Tbird1044 11-22-2014 01:21 AM

It's easy to check the PCV valve setup by checking if you pull a good vacuum through the valve when the engine is running. The original oil breather cap should be replaced with a cap that has a hose fitting on it, so you can run that hose off of the cap to a small filter installed in the air cleaner. This serves two purposes. If you have excess vapors they will be directed back to the air cleaner. If your PCV valve is pulling more vacuum than you have blowby, then it will pull filtered air back into your engine crankcase.
Nyles

1960_tbirdman 11-25-2014 02:29 PM

I know we installed the spacer correctly as we double checked that.

I will check the vacuum and see. I am getting oil out the breather cap as well.

Thanks for replies.


All times are GMT -4. The time now is 03:06 PM.

Powered by vBulletin® Version 3.6.8
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Any submissions to this site and any post on this site becomes property of Squarebirds.org . The webmasters reserve the right to edit and modify any submissions to this site. All material on this is site is copyrighted by the Squarebirds.org. Reproduction by any means other than for personal use is strictly prohibited. Permission to use material on this site can be obtained by contacting the webmasters. Copyright 2002-2016 by Squarebirds.org.