Squarebirds, Rocketbirds, and Fifties/Sixties Ford Discussion Forum

Squarebirds, Rocketbirds, and Fifties/Sixties Ford Discussion Forum (http://squarebirds.org/vbulletin/index.php)
-   1961 To 1963 Bulletbirds, Rocketbirds - General Technical Discussion (http://squarebirds.org/vbulletin/forumdisplay.php?f=24)
-   -   need help identifying these parts??? (http://squarebirds.org/vbulletin/showthread.php?t=16341)

btiberend 12-31-2013 12:26 AM

need help identifying these parts???
 
2 Attachment(s)
I am 100% pretty close to firing up the 1962 dirty bird, I went thru and completely rebuilt the top end of my FE 390' rebuilt the heads, new valves and such, a little bowl work , and cleaned em up. New lifters, and push rods.I have her all back together now now I have a few questions on the remaining holes in the intake manifold, there is what looks like a vacuum hole that takes some sort of fitting' its just of and the tbe passenger side of the carb.... the other one is right behind the distributor? Any pics of how these set up would be of great assistance

simplyconnected 12-31-2013 12:55 AM

The top picture is showing an open and rather large vacuum fitting for your brake booster. The bottom picture is showing your temperature sending unit without the wire attached. There is another sending unit that goes by the oil filter for your 'OIL' light. - Dave

btiberend 12-31-2013 01:14 AM

Thanks again dave...
The brake booster fitting looks rather large? It does look as if it was replced to rig it up an make do at one time. Where could I get that brake booster fitting (the right one) and would that keep me from firing up?

The temperature sending unit? Where would that wire connect?

Thanks again

simplyconnected 12-31-2013 05:23 AM

The booster fitting looks stock. You need it that large.

As for the temp sending unit; there is a red-white wire coming from your firewall that slips on top of that sending unit. It runs your TEMP gauge.

When you install your engine, make double-sure you have good grounds. Even the band that goes around the coil has a tit that 'digs' into the coil case. Make sure the coil is bare at that point. I run my battery NEG to my bell housing, close to the starter motor, not to the water pump. You should have a ground strap on the driver's side head, that connects to the firewall. This is important. Electricity takes the path of least resistance. You don't want current from your lamps and accessories, going through bearings (u-joints, etc.), trying to return to the battery. - Dave

btiberend 12-31-2013 11:58 AM

Bake booster, thanks good to know, I cant wait to get home tonight and seeif iI can find where he connects.

Red/ wire.... I think I know that wire... it has a push-on style connector?

I am also going to check the battery ground wire, I dont think it's running to the bell housing right now. I do have a ground strap coming off the firewall but I have him tied down at the intake manifold thru-bolt to head on the rear passenger side.

Getting excited about firing her up


All times are GMT -4. The time now is 04:49 PM.

Powered by vBulletin® Version 3.6.8
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Any submissions to this site and any post on this site becomes property of Squarebirds.org . The webmasters reserve the right to edit and modify any submissions to this site. All material on this is site is copyrighted by the Squarebirds.org. Reproduction by any means other than for personal use is strictly prohibited. Permission to use material on this site can be obtained by contacting the webmasters. Copyright 2002-2016 by Squarebirds.org.