Squarebirds, Rocketbirds, and Fifties/Sixties Ford Discussion Forum

Squarebirds, Rocketbirds, and Fifties/Sixties Ford Discussion Forum (http://squarebirds.org/vbulletin/index.php)
-   1955 To 1957 Little Birds - General Technical Discussion (http://squarebirds.org/vbulletin/forumdisplay.php?f=61)
-   -   Importance of Brake Adjustment (http://squarebirds.org/vbulletin/showthread.php?t=11202)

Jimz Bird 05-20-2011 05:27 PM

Importance of Brake Adjustment
Good article on Why to maintain good brake adjustment especially with a dual disc/drum system.


REM 05-20-2011 05:41 PM

A lot of good reading but not all accurate.
Self adjusting brakes will self adjust with normal driving.
If they are loose enough to catch a click on the adjuster with a forward stop it will stay caught and adjust the next time you back up and set the brake. No need to deliberately go forward and back and set the brakes each time to adjust them.
If they don't stay adjusted properly with normal driving something is sticking, broken or just not working properly.

Jimz Bird 05-21-2011 01:21 AM

Good additional thoughts and something we definitely want to monitor if we put self adjusters on.

Another "tick" to put on the "Periodic Maintenance" chart.:)

Thanks for the additional info.

simplyconnected 05-21-2011 06:03 PM

Jim and REM, good thoughts and thanks for the thread. I can't help but believe some folks don't fully understand drum brakes. They are nearly stupid-simple, but they work real well with excellent dependability.

Originally, brakes were strictly mechanical (you could depend your life on them). Then, hydraulics were used WITH an Emergency Brake override (that was strictly mechanical).

Ok, so hydraulics expand two shoes instead of cables and cams.

So, what stops the shoes from rotating within the drums? "For every action there is an opposite and equal reaction." Brake shoes 'float' with those skinny little piston rods.

It's that HUGE pin at the top. The shoes expand, grabbing the drum, and they rotate until the back shoe 'seats' against the "Brake Shoe Anchor" pin. Think about this; if we only had one direction (Forward), the wheel cylinder would only need one piston because the 'back' shoe is always solid against the anchor, even when the shoes retract. The only time the back shoe comes off the anchor is when your car changes direction. Then, the opposite shoe becomes the 'back' shoe, respectively.

Because we rarely go backwards, and the 'back' shoe is normally on the anchor, that shoe lining needs to be longer than the front lining. That's why Primary & Secondary linings are necessary. For the same reasons, we install our self-adjuster cables on the rear brake shoe. The only time the cable has tension is when the car is reversing during braking. And, the only function the cable serves is to lift the ratchet on the star wheel for when the car goes forward again. So, this 'rocking' motion of the brake shoes is necessary to self-adjust. It needs braking in both directions to work.

The article misses a couple points:
* Some self adjusters (like on my Tempo) simply expand the tops of the shoes farther and farther out. They bring the shoes closer to the drums, but the pistons follow and can eventually come out of their bores causing catastrophic brake failure (evidenced by brake fluid leaking out of the wheel).

Bottom star wheels (and self adjusters) compensate for lining wear by expanding the diameter of the shoes.

* Disk brakes have HUGE pistons. That's why the front-brake reservoir in the M/C is always the largest one. Ford uses the rear bowl and GM uses the front of the M/C for the front hydraulic circuit.

The article offers some good ideas but it fails to mention that a combination proportioning valve shuts off the bleeding circuit, to conserve brake fluid.

I firmly believe every car on the road should have a dual M/C because a hose can burst at any time, forewarned or not, regardless of Drum or Disk Brakes. The author must believe that too because he wrote about installing one on his own car. - Dave

Jimz Bird 05-22-2011 01:59 AM


Once again, Thanks for chiming in with the "Nitty-Gritty" (Brake Dust that is:) )

All very interesting and the explanation of the long and short of the shoes.

I, for one, appreciate the detail that you add to these threads.

simplyconnected 05-22-2011 03:28 AM

Thanks Jim, I think it's important to understand how drum brakes work for better assembly.

God knows, I've seen every combination of mismatched shoes on a wheel; two primary or secondary shoes on the same wheel, primary shoe on the wrong side, etc. Some guys never knew there was a difference and couldn't understand why their new brakes pulled so badly.

But in fairness, nobody can actually see drum brakes function. That makes it harder to understand what's really happening. - Dave

All times are GMT -4. The time now is 10:52 AM.

Powered by vBulletin® Version 3.6.8
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
Any submissions to this site and any post on this site becomes property of Squarebirds.org . The webmasters reserve the right to edit and modify any submissions to this site. All material on this is site is copyrighted by the Squarebirds.org. Reproduction by any means other than for personal use is strictly prohibited. Permission to use material on this site can be obtained by contacting the webmasters. Copyright 2002-2016 by Squarebirds.org.