Announcement

Collapse
No announcement yet.

Holley 4160

Collapse
X
  • Filter
  • Time
  • Show
Clear All
new posts

  • Holley 4160

    Hi Guys

    How many of you are running a Holley on their 352? Mine came with one installed and other than having to replace the needle and seat it's been OK, but I ran the numbers off the carb and discovered it's a 450 CFM model. I still have the original in a box but it needs to be rebuilt (200.00 locally) and also read that the kickdown ongoing issues I'm having might be related to the carb as well.

    I was reading that the lock down screw needs to be removed for automatic transmissions and there should be an adjustment and spring on the carb for the kickdown. I'm not sure though. Anyone else running it on their squarebird?
    Scott
    South Delta, BC, Canada
    1960 White T-Bird, PS, PB that's it
    Red Leather Interior!
    www.squarebirds.org/users/sidewalkman
    Thunderbird Registry #61266
    http://www.squarebirds.org/picture_g...ibrary/trl.htm

  • #2
    yes I am. it was installed on mine as well at the time I purchased it. unfortunately it is running fine so I can't relate to any of the issues you are having. I have had a stuck float that was fixed quickly with a tap on the bowl and it has not reoccurred in over a year. I however have all intentions if it ever gives me any issue to install and Edelbrock.

    Comment


    • #3
      Scott,
      Sorry the progress on mine to fix the fire damage has been slow but funny thing is I just about finished up this evening and have some pics.

      I'm using the Holley 4160 (aluminum version). The original air cleaner works but not as well as with the original 4100 that came on the car.


      So when I bought it the folks at Holley told me it was a good replacement carb for the 4100. It bolted on to the intake but the linkage hit the intake and wouldn't move.


      They told me I could cut the bottom of the linkage off so that it missed the intake and wouldn't void the warranty (yes I have it in writing - )


      Here it is at wide open throttle - make sure yours isn't hitting anything.


      At the transmission linkage I had to install some washers under the linkage to make it miss the intake - only about 1/8 clearance but it works (this is also wide open throttle but not with the pedal pressed to the floor to pull the kickdown in). I was just holding the throttle open with my hand.


      Overall view


      My accelerator pedal rod is about 8 7/8


      I had to straighten the accelerator linkage rod a small amount to make it longer plus drill a tiny hole in the end to put a cotter pin and washer behind the carb linkage - now measures 8 1/8 from where it connects to the carb from the pin at the linkage.


      There is about 3/4 inch of threads showing on the kickdown linkage.

      Also had to modify the air cleaner a bit because the linkage was hitting the air cleaner so it would not return to idle very well (lucky thing I have an old spare air cleaner to modify and can put my original in a box for later)


      The snorkle just misses my PCV valve.


      Not completely happy with it at the moment - sounds like the engine is really lean. Supposedly mine is a 600 CFM carb. Maybe the sound is just normal but has always been rich with the 4100 - I'll just have to see. Went through the works setting the points, timing, etc - no difference. Decent throttle response but I haven't had it out on the highway yet to check the kickdown response so all my linkage measurements may change.

      I only have the standard wedge spacer under the carb (with gaskets). I have a rebuild kit for my 4100 and may just pull the Holley off if it doesn't improve on the highway and with a little running in.

      Eric

      Comment


      • #4
        Hi Eric

        Thanks for this, I've attached the picture of the locking screw on the carb. Do you still have yours in place, doesn't look like you do.

        I'm sidetracked right now, the lines running to the PS Ram developed a leak, I tried to Teflon tape the threads, ended up stripping the fitting so new lines are ordered. I don't want to really do anything that requires starting it till the lines are back on. I've already puked a quart of PS fluid everywhere. I'll dial in the pedal linkage and rough in the rest as per the manual and see where that takes me. I'm going to try the carb without the locking screw as everything I have says remove it for automatics, unless the kickdown linkage attached directly to the throttle arm
        Attached Files
        Scott
        South Delta, BC, Canada
        1960 White T-Bird, PS, PB that's it
        Red Leather Interior!
        www.squarebirds.org/users/sidewalkman
        Thunderbird Registry #61266
        http://www.squarebirds.org/picture_g...ibrary/trl.htm

        Comment


        • #5
          The screw Holley states to remove is in order to allow the A.T. "kick-down" lever to operate on the carburetor linkage shaft. Allowing this lever motion, along with a cap-screw, threaded nut & return spring are intended for attachment & operation of the "kick-down" rod linkage which is used on C4 & C6 transmission applications. On these applications a single steel tube linkage attaches from the carburetor kick-down lever down to the transmission's lever.
          This is not applicable in your installation, if you retain the C.O.M. transmission & factory linkage. Scott.

          Comment


          • #6
            Originally posted by pbf777 View Post
            The screw Holley states to remove is in order to allow the A.T. "kick-down" lever to operate on the carburetor linkage shaft. Allowing this lever motion, along with a cap-screw, threaded nut & return spring are intended for attachment & operation of the "kick-down" rod linkage which is used on C4 & C6 transmission applications. On these applications a single steel tube linkage attaches from the carburetor kick-down lever down to the transmission's lever.
            This is not applicable in your installation, if you retain the C.O.M. transmission & factory linkage. Scott.
            Perfect, thanks. The instructions were rather vague.
            Scott
            South Delta, BC, Canada
            1960 White T-Bird, PS, PB that's it
            Red Leather Interior!
            www.squarebirds.org/users/sidewalkman
            Thunderbird Registry #61266
            http://www.squarebirds.org/picture_g...ibrary/trl.htm

            Comment

            Working...
            X