View Full Version : 60 Golde Top seal install
08-14-2010, 09:33 PM
I have worked through the sliding roof mechanism instructions in this forum. My sliding roof operates well now. Thanks for the helpful info.
Now I need to install the roof seals. I purchased the rubber seal, rear felt seal and car body seal. Can someone please describe (photos?) how the seals should be positioned to get both a good water seal and easy sliding roof operation? In particular, how should the rear felt and car body seal beads be aligned vertically relative to the panel or roof? How should the rear felt seal and car body seal overlap at the sliding roof sides? I will appreciate any help that someone can provide.
08-27-2010, 01:33 PM
The opening panel seal should be install so that the bead edge is just slightly, not much! above the sliding panel, so when you close the sliding panel onto the bead it forms a seal as the bead compress.
Felt seal is for the rear of the sliding panel, and that bead should just sit slightly raised up so when you turn the sunroof handle the seal compress again against the roof panel to form a seal. Post your email address and i will try and find some photos for you.
08-29-2010, 12:02 PM
Would you mind sending photos of the seal installation to me, also. My email is firstname.lastname@example.org.
09-09-2010, 01:40 AM
Thanks for the description. My email address is email@example.com. If you can send photos that would be great.
I'm also interested in how the two seals meet on the side. It seems like there might be a tendency to bind the sliding panel from lifting as you turn the handle. I appreciate your help.
03-27-2012, 05:20 PM
I´m replacing seals on my 1960 Golde top and could use some help. The old seals were painted over or otherwise gone. I think some were missing altogether. If anyone can help on what kind of seals go where and where to get new seals, please send e-mail to: firstname.lastname@example.org
03-28-2012, 08:43 AM
I am also interested in the photos,wonder if you can send to me to.My mail:email@example.com
03-28-2012, 12:37 PM
It has been some months since Kevin was last on the Forum. I have emailed him in England to see if he can come up on the Forum and give you some assistance.
07-23-2015, 01:52 PM
I'd love to hear about a sunroof seal soure ,for my 60 ,I think someone in the past has covered over the drain holes I looked at the old thread about how to apply them
07-23-2015, 07:51 PM
Sunroof seals are available at the Bird Nest in Oregon.
If you put in new seals, let us know how they work!
08-20-2016, 11:14 AM
I am about ready to install my sunroof. I purchased new seals from Bird Nest and have read everything I can find regarding installation. If anyone has photos of the seals installed or could take some photos and post them it will be greatly appreciated.
08-24-2016, 12:01 PM
I only replaced the seal that goes across the back of the sliding panel (listed in the Bird Nest catalog as "B. Rear Felt Seal"). It sits along the back side of the panel raised slightly above the top of the panel. I tried to take pictures, but they do not show anything because this seal is barely visible except when looking straight down with the sunroof closed. My sunroof does not leak, so I have not installed the seal around the front of the opening. There is a gap around the front and sides, but water goes into the channel and drains through the drain holes front and rear. Hope this helps.
08-25-2016, 09:48 AM
Harry hope you are well.
Missed you at our Calgary Thunderbird Club S&S last Saturday at Knob Hill Community Center. Were you away?
08-25-2016, 06:17 PM
Hi Dan - all is well here. We had company from Arizona and I was unable to make it down for your S & S. Hope you and Marg are well and enjoying our wet summer. Harry
08-26-2016, 09:49 AM
Thanks for the information. I need to replace all three on my car and any help is appreciated. Hopefully, someone may have taken some pictures and will post them. if not, it will be trial and error. Thanks again.
vBulletin® v3.6.8, Copyright ©2000-2017, Jelsoft Enterprises Ltd.